1. Turn off the power and unplug the charging cable: If your Bluetooth headset cannot be charged after water, it is recommended to turn off the power and unplug the charging cable immediately to avoid short circuit or other problems.
2. Take out the battery and dry it: If the battery of your Bluetooth headset can be removed, try removing the battery and drying it before reinstalling it. This may bring the device back to normal.
3. Desiccant moisture absorption: You can use some moisture absorption agents, such as white rice or diatomaceous earth, etc., put the Bluetooth headset into a sealed bag, and put moisture absorption agent, and then wait for a period of time before trying to charge.
4. Send for repair: If the above methods are ineffective, it is recommended to send the equipment to a professional repair shop for inspection and repair to avoid damage to the equipment and circuit. It should be noted that if your Bluetooth headset is flooded, try not to use heating equipment such as a hair dryer to dry it, so as not to cause more damage
If the Apple Bluetooth headset water can not be charged, you can try the following solutions:
< br >
Do not charge the earphone immediately after it is flooded, which can easily lead to short circuit or burn the internal circuit of the earphone. You can wipe the water on the surface and put it in the desiccant to absorb moisture.
Use a hair dryer to dry the moisture inside the headset, but be careful not to use too much wind and too high a temperature to avoid damaging the headset.
If you still can't charge it, you can put the headset in the charging case and plug it into the USB port to charge it.
If the above methods do not work, you can contact Apple customer service or go to Apple authorized repair point for repair.
It should be noted that the earphone should not be used immediately after water, and it should be dried first to avoid damage to the earphone. At the same time, it is recommended to pay attention to protection when using headphones to avoid water or other damage.
If the Apple Bluetooth headset cannot be charged after water, first of all, it should be interrupted from the power supply immediately, and put the headset in a dry and ventilated place to dry. Do not use hair dryers or heating equipment to speed up drying, so as not to damage the internal circuit. When the headphones are completely dry, try recharging them. If the problem persists, you may need to contact Apple customer service or a professional repairman to repair or replace the part. Remember that water flooding can cause serious damage, so early treatment is key.
high quality
There are generally two possible reasons why the Bluetooth headset is not charged with water.
< br >
The first type of Bluetooth headset internal failure, such as battery or circuit damage, charging interface short circuit, etc.
< br >
If it is for the above reasons, the headphones need to be sent for repair
The second charger or data cable has a problem, resulting in charging cannot continue.
Replace the matching charger or data cable to recharge
1. Remove the AirPods from the charging case and wipe the AirPods and the charging case with facial tissue or cotton cloth.
2, blow dry with a hair dryer (remember to use cold air), place in a well-ventilated place within 12 hours, do not put AirPods into the charging case or use.
3, take a plastic bag, put AirPods and charging case into the plastic bag, put several packages of desiccant or dehumidifier inside, and tie the plastic bag.
4. If there is no dehumidifier and desiccant, AirPods and charging boxes can be placed in a rice bucket filled with rice (plastic bags are recommended).
5, if through the above method to solve or found that AirPods can not operate normally, it can only be sent to find a professional repair.
< br >
Method 1:
< br >
Hair dryer method: This method can be said to be the most direct violence, because the Bluetooth headset is small, of course, if the water situation is also serious, using a hair dryer to blow directly on the machine, usually after a period of time can be repaired, but need to control the temperature.
< br >
Method 2:
< br >
Place method: Drain the water of the earphone and put the earphone into the rice jar with a vacuum belt, so that it can be placed for a few days.
< br >
Method 3:
< br >
Maintenance method: This method will lose the risk of warranty, it is recommended that users use after the warranty, directly disassemble and dry with hot air, of course, you need to pay attention to the loss of this component.
< br >
It is necessary to take timely measures to repair because water will cause short circuit of electronic products, and the battery will not be charged if the earphone is not treated in time after soaking in water.
First of all, it should be wiped clean on the surface of the headset, and then put in a ventilated place to dry, but not directly exposed.
If it is not repaired within 24 hours, it is recommended to get a professional after-sales service center for repair.