The correct way to power on (start the battery) is as follows:
1. Find a working car, park both cars close to each other and make sure the engines of both cars are turned off.
2. Take out the red positive jumper clip and connect it to the positive battery end of the locked working car.
3. Connect the other end of the red positive jumper clip to the positive battery end of the car that you want to start.
4. Take out the black negative jumper clip and connect it to the negative battery end of the work car. 5. Attach the other end of the black negative jumper clip to the metal part of the car that needs to be started, such as the metal bracket on the bonnet or the ground point on the engine. 6. Ensure that all jumper clips are securely connected and that they are not in direct contact with other metal parts.
7. Start the engine of the work car and keep idle.
8. Wait a few minutes for the battery to charge for some time.
9. Start the car that needs to be started. If the startup is successful, the jumper should be disconnected immediately to prevent current backflow.
10. If the startup attempt fails, wait a few minutes again and make sure all connectors are firmly in place. Then try starting again.
Please note the following:
- The battery polarity of conventional internal combustion engine vehicles is positive red and negative black. Observe carefully to ensure proper connection.
- Ensure that there is no metal contact between the two vehicles during the electrocution process to avoid the risk of electric shock.
- Try to avoid touching battery terminals and other metal parts to prevent electric shock.
- Ensure that both the vehicle and the jumper are stable and avoid moving or rocking during the power trip.
- Electrotripping is a temporary solution that requires timely repair or replacement of the battery to solve the vehicle starting problem.
If you are not familiar with the operation of lapping, please seek professional help or consult your car manufacturer for more detailed guidance.
Prepare two battery lines, the rescue vehicle and the rescue vehicle should be head to head together, the rescue vehicle does not have to turn off.
< br >
Find the batteries of the two cars, distinguish the positive and negative terminals of the battery, do not connect the positive and negative terminals wrong.
< br >
First, a section of the red positive battery wire is connected to the positive terminal of the rescue vehicle battery, and then the other end is connected to the positive terminal of the rescue vehicle battery.
< br >
Similarly, one section of the black negative battery wire is connected to the negative terminal of the rescue vehicle battery, and the other end is connected to the negative terminal of the rescue vehicle battery.
To power on Rez properly, first make sure both vehicles are stopped and turn off all electrical equipment.
Then, connect the red positive cable to the positive terminal of the normal battery, and then connect the other end to the positive terminal of Rez.
Next, connect the black negative cable to the negative end of the normal battery, and then connect the other end to a metal part of Reiz, such as the engine bracket.
Once the cable connection is secure, start the normal vehicle and keep it running for a few minutes before starting Reiz.
Finally, remove the cable gradually, first remove the negative electrode and then remove the positive electrode to ensure safety. Remember to be careful when powering to avoid touching metal parts or short circuits.
Reiz needs to pay attention to the following points:
First, the red and black cable clips connecting the positive and negative terminals of the battery should be connected to the positive and negative terminals of the battery of the two vehicles respectively;
Second, start the main engine and keep it idle, then start the slave engine again. Before disconnecting the cable, turn off any electrical equipment from the car and remove the cable clamp in reverse order. Finally, it is recommended to read the vehicle manual carefully before the vehicle is powered on, understand the specific methods of the vehicle and comply with the relevant safety regulations.
Hello, the correct way for Reiz to connect is as follows:
1. Park both cars on a flat surface and turn off the engine.
2. Open the hoods of both cars.
3. Use the red positive cable clamp to connect the positive terminal to the positive battery of the vehicle that is already fully charged. The positive battery has a \"\" sign on it.
4. Use the black negative cable clip to connect the other end to the negative battery of the vehicle that has been fully charged. The negative battery has a \"-\" sign on it.
5. Connect the red positive cable clip at the other end to the positive battery of the vehicle that needs to be powered on.
6. Connect the black negative cable clip on the other end to the metal part of the vehicle that needs to be powered, such as the metal rod on the hood.
7. Make sure the cable is securely connected and that the cable does not come into contact with any moving parts.
8. Start the fully charged vehicle and keep it running for a few minutes to transfer power to the vehicle that needs a ride.
9. Start the vehicle that needs a ride and keep it running for a few minutes.
10. Remove the cable in the reverse order: Remove the black negative cable clip first, and then remove the red positive cable clip.
Note: When performing Lapping operations, be sure to follow the correct procedures and safe operations to avoid hazards. If you are not sure how to do it properly, it is recommended to seek the help of a professional vehicle repairman.