Charge it! I don't know what you mean!
First of all, both outside and inside!
What about the outside? Unlike the trouble of what application form is written on the document, in the countryside, just talk to the electrician! Wires are public, of course, said from the door of your knife or electricity meter outside, your indoor people will not give you run!
The indoor ones are a little more troublesome! One is embedded, that is, inside the main body of the house, together with the main body, through the wall. This kind of bad is that the tube will be impenetrable, especially the unprofessional themselves, like cement slag what fell into the tube, or the corner, and then how can not wear the past, it is not beautiful!
The second kind is after the main body is good, and most of the rural areas are such bright lines. How to run the line, through the pipe or the line slot, the line slot is better! Look nice. It looks flat and straight
There is also a slot, that is, a slot is opened on the wall surface, the line is put in and then filled with cement, this is not recommended for large-scale construction, too much trouble! There is a period of impassable transformation can also! You want to look good, be my guest!
And with this technology, if you can't connect a switch! I don't recommend doing it myself anymore. Wiring should also pay attention to, the two branches each cross a clockwise a counterclockwise winding, so the more pull tighter, you can Baidu!
Line quality should also pay attention to! General household standard 4 square copper wire is almost can drive about seven kilowatts! Depending on your electricity consumption! Aluminum wire is not recommended to consider, easy to oxidize, and easy to have problems with a long time!
In general. No practical experience is not recommended to do it yourself! The happiness of doing that well is beyond words! I wish you success! Thank you!
First choose wire:
1, air conditioning and electric heating, bath and other high-power electrical appliances use more than 4 square copper wire, preferably six square, so as to avoid overload and burn the line. Other electrical appliances all use 2.5 square single strand copper wire is enough. Including the range hood in your kitchen.
2. Install a switchboard in the living room. First of all, there is an air switch under your entry meter, if its capacity is 100 amp, then the total air switch inside the switchboard can choose 60 amp, and then next to the total air switch is the lighting circuit breaker, the lighting circuit breaker of each room should be separated, can not share a circuit breaker, in case there is a problem with the lighting in which room. You won't be able to tell the difference or figure out what the fault is!
3. The general lighting circuit breaker can choose 16 Ann, the air conditioner can choose 32 Ann, and the lamp switch on the wall can choose 10 Ann.
4. The sockets in each room should be separated separately, and all sockets in a room can be controlled by a leakage socket; Except for the air conditioner, the air conditioner socket should also be controlled by a separate leakage socket. The air conditioning socket on the wall can choose 16 Ann, the cabinet machine in the living room can choose to use 16 Ann or 32 Ann air switch to control, can not use the socket, your plug and socket are easy to burn out for a long time.
5, although the time to use more lines, but because the lighting and ordinary sockets, air conditioning, bath socket lines are independent of each other, do not affect each other, so you can save a lot of trouble.
6. Be sure to remember that the lighting and socket can not be separated as before, and the line can be cut from the middle, and the most fault is in the connector part. You and the electrician won't be able to tell the difference and figure out what's wrong.
7. The meaning is the dark line, the line has been buried in the wall, if there is no dark line, you need to take the open line, you also need to buy the slot plate line. Buy as needed at that time
Now whether it is rural or urban are paying attention to the installation and transformation of water and electricity, the first installation after less problems, the second is now more and more household appliances, the location and height of the reserved socket is very important, water and electricity installation does not care to bring trouble to life. I don't think there is much difference between rural and urban hydropower installations. Now I briefly talk about the general meaning of rural circuit installation, the home will now install a distribution box, and the location of the distribution box is also very important, the distribution box as far as possible to choose the middle position of the overall house, because the wire can be divided on both sides, so the biggest advantage is that the length of the wire can be shortened, it is convenient to thread later, and it also avoids the heat caused by the wire being too long. There is also the ability to save materials, if the distribution box is chosen at one end of the house, the wire will be worn far, and the threading will be difficult to maintain. Now the electricity consumption is relatively large, so it will be divided into multiple circuits, under normal circumstances, all the way lighting, air conditioning, kitchen, bathroom, all the rest of the ordinary socket all the way, the advantage of this is that it can be shunted, but also to avoid a fault as a total power outage, if the budget is sufficient, you can also press this subcircuit, There is also a simple one that divides a room into a loop, so that there will be no multiple lines in a room, which can save a lot of materials and working hours, and can also play the role of diversion and the role of a fault all power outage. I just said a general framework, the location of the specific socket should be determined according to the layout of each family, and the height of the socket is basically the same. For example, the switch is 1.4 meters, the ordinary socket is 300 centimeters, the air conditioning socket is 1.8 meters, and it can also be adjusted according to the height of its own furniture, in a word, the position of the socket must be selected to the right height can be changed according to the actual situation.
I am very happy to answer your question, if you are learning an electrician, or have a certain electrician foundation, it is absolutely no problem to install yourself, if you are not interested in this electricity or have never been in contact with this aspect, personal advice or do not do it, after all, this electricity does not recognize people, this is not to be joked about, responsible for yourself is also responsible for others, Since you have proposed to install it yourself, there may be a certain basis, the following details about how to operate the basic knowledge of electricity:
1: First you have to understand the layout of this house, be sure to get it clear.
2: Calculate the total power of all electrical appliances in the room to use how much main line?
3: Reserve points for water supply and drainage, basically accurate, including the position of all electricity.
4: Some of the layout of other rooms, such as the location of sockets, switches... Those are actually very simple, specific can be arranged according to the actual.
4: If you do not understand the place, you can look up some information on the Internet.
Rural houses installed before the wire to do three lines into the household? And then the distribution box and the leakage circuit breaker? Line thickness selection suitable for high-power line at home?
To install electricity in your own house, you must first have certain electrician knowledge, because people who do not understand electricity, electricity is harmful to the person to death. People who do not have professional electrician knowledge or do not install their own electricity, short circuit will cause a fire, electricity is ruthless. To install electricity, we must first design the way of the wire circuit of a building, and the lines of the living room, the room, the stairs, the bathroom, etc., must be known one by one. The electricity load of the whole building has to be calculated, and how many square lines can be used. And whether to use copper wire or aluminum wire should be considered, safety first!
I recommend that you still find a professional, because water and electricity is the artery of the house. It's very troublesome if you don't do it properly.
Install your own electricity must pay attention to, first you want to install your own electricity shows that you must have a certain understanding of the circuit. Just like me, an amateur. The most important thing is safety, including the safety of installation, and the safety of future use. Many steps needless to say, the key line size must be enough. Second, the wire connection must be tight. The most critical point, which is also easy to ignore, must be wrapped tightly when wrapping the electrical tape, which is the most important. I hope I can help you,
What I didn't understand was the electricity outside the house, or the electricity in the house, if the electricity outside the house, the station workers to press, their own installation is equal to private pull random, dangerous not to say fines, the words in the house can be installed by themselves, pull two main lines first, buy 4 square, to use copper wire, it is best not to use aluminum wire, easy oxidation, two lines go separately, Use insulated tubes to cover, leading to each room with 2.5 square copper wire is enough, wire joints with soldering, insulation tape wrapped, light switch control fire wire, I do not know if it is right, when my house was built, the house lights ah, switches, plug board are pressed by myself
Rural self-built houses newly installed (increased capacity) electricity needs to provide the following information:
1, customer identification information;
2. Proof of property ownership of electric address;
3. Bank fee deduction information. If the electricity address does not have a property ownership certificate, the land planning department needs to confirm that the electricity address does not involve illegal construction, rush construction and violation of planning land and other problems. You can follow and bind the \"Southern Power Grid 95598\" public platform > \"My electricity\" > \"Business Management\" > \"Electricity application\" > Select the corresponding business type, view the business description and management process > Click \"Management\" > Fill in the basic information and submit it.
With the progress of The Times, social development changes. There has also been a change in rural housing, which used to be cave dwellings or wool-grass huts. Rural housing has changed, from the round stone kilns of the past to the flat suites with clean tiled fronts and polished floors.
The rural room reform circuit is changed in daily life's own needs, such as you need to lie in bed to look at the mobile phone, look for a long time the mobile phone needs to be charged, but you also need to continue to look, then you need to add a power socket at the bedside. Electrical outlets and wires are now concealed for aesthetic reasons. You must first determine the position of the power socket, in the determination of the power line from that position to connect her, after determining, you need to chisel 2 cm (cm) of the line slot, in the buried line pipe, with cement mortar to fix the line pipe groove and the wall touch flat, in the line to connect the power supply, connect the socket, open the power switch. Strong and weak electricity change electricity method basically the same hope can help you.
Take the household register, ID card, go to the power supply office to apply for it, local policies are not the same, some want money