First buy an original stove brand ignition needle back, must be the same model, not the model can not be put into. Open the outer cover, pull it out and replace it with a new one
< br >
1, the gas stove ignition line input power supply should be 200-240AC (green front, blue common line), if reverse connection, only the polarity is the same, the gas stove incinerator can operate normally; However, if the polarity is not consistent, it is very simple to burn the fuse or directly burn the incinerator, so we must be careful when wiring.
< br >
2. It is necessary for the gas stove igniter to accurately wire the function of each line color before it can be powered on. The grounding cable must be connected to the line connected to the support of the gas stove itself. The high-voltage incineration line and the induction line can not be tested against each other, otherwise the induction system will fail until scrapped. The high voltage line and the induction line should not be connected too long, which will affect the high voltage ignition strength and induction.
3, the high pressure ignition needle can not be put on the ground, otherwise it will affect the high pressure coil life of the gas stove incinerator. The sensor needle will cause a bad sensing, it will alarm, stop operating. The high pressure arc starting interval of the incineration needle should be 3-6MM, which should not be too wide, otherwise it will simply appear in the use of no incineration, and it will simply burn the gas stove incinerator.
How to change the ignition core of the gas stove? Gas stove cleaning method?
Gas stove cleaning method?
< br >
1, we pour an appropriate amount of dishwashing liquid on the stove, and then cut the rest of the radish head, use it to wash the dishwashing liquid. When it is almost wiped, it is OK to wipe it with a rag again, so that the stove can be wiped with a new look. Sliced cucumbers and carrots can also be used instead, but white radishes work best.
< br >
2. Potato skin: Wipe the stove directly with the inner skin of potato skin, and then clean it again with hot water.
< br >
3, white vinegar and warm water: Mix two spoons of white vinegar with 200 ml of warm water, and then use a sponge and environmentally friendly loofah, dip in this \"hot vinegar water\" to clean the stainless steel stove, you can make it bright as new.
< br >
4, with boiling fire rack and for the vent \"pick teeth\" : to take the stove down, one by one with a toothpick to clean the vent once. The carbides and coke accumulated on the stove can be removed with a small fine brush, or a fine wire can be used to Pierce the fire hole one by one.
5. It is necessary to regularly test the tightness of the gas supply rubber hose and test whether the gas supply hose interface is sealed. To prevent gas supply rubber hose aging or cracks, resulting in gas leakage, light gas poisoning, heavy cause fire.
2. Unscrew screws.
3. Open the seal cover.
4. Lift the tempered glass panel.
5, Install the new ignition needle, test the ignition situation, the ignition needle perforated through the line.
6. Locate and place the needle and connect the wire.
7. Test whether the installation is normal.
8, the switch rust, clean with rust remover, drop some lubricating oil (peanut oil is also OK), convenient effect.
？
Precautions for using cookware:
1, the stove should be placed in the shelter, or increase the wind shield to prevent the fire from the bottom of the pot.
2, adjust the size of the air inlet, so that the gas is fully burned, the burning flame should be blue.
3, fully do the preparation work before cooking and then ignition to prevent \"hanging fire\".
4, soup, stew things, should be brought to a boil with a high fire, and then use a low fire to keep the pot boiling without overflow.
？
5, the reasonable use of the stove shelf, the height of the flame should make the outer flame contact the bottom of the pot, so that the combustion efficiency is the highest.
6, adjust the size of the fire according to the size of the pot bottom, so that the fire is slightly bent after contact with the pot and the pot bottom, and the fire is appropriate to lick the bottom.
7. Using a pan with a large diameter saves gas than a pan with a sharp bottom.
It can be replaced by opening the fixing screws around the stove head successively.
When the gas stove is working, the gas enters the stove from the intake pipe and is adjusted by the gas valve (adjusted by the user through the knob) into the stove head. At the same time, some air is mixed (this part of air is called primary air), and the mixed gas is emitted from the fire hole of the distributor and ignited by the ignition device to form a flame (the air required for combustion is called secondary air). These flames are used to heat cooking utensils placed on pot holders.
Next to the stove center (on the front of the stove, under a stainless steel ring) there are three screws, all of which can be unscrewed to remove the stove surface, and then the screws on the stove top can be unscrewed, also three, some of the stove is screwed inside, some of the stove is screwed on the bottom, turn the stove head over and you can see the fixed part of the ignition needle, as long as the fixed circlip of the ignition needle can be removed, Be careful not to remove the spring above the circlip.
The gas stove core is the ignition needle.
one
Lift up the gas stove.
two
Unscrew screws.
three
Open the seal cover.
four
Lift the tempered glass panel