1, Plug the accessory camera harness into the rear license light drilling hole, and then directly into the card. The red line is the line used to connect the video signal.
< br >
2. Remove the liner of the trunk, pull out the waterproof cable ring, use the traction wire to pull out the camera harness to the trunk, lead the camera harness and data connector to the cable hole of the rubber ring, and finally install the waterproof rubber ring;
< br >
3. Remove the decorative lining board on the left side of the trunk, connect the data power extension cable with the camera wiring harness, and lead out from the rear trim board along the original car wiring harness;
< br >
4. Open the sealing rubber strip on the left side of the door of the back seat, pull the cable into the back seat cabin, and pull out the integrated plug of the data power supply and the remaining extension cable;
< br >
5, restore the trunk, the extension line along the door of the rubber strip into the plastic plate gap, until the cockpit door; 5. Remove the storage box under the headlight, pass over the OBD interface, and then connect the wiring port with the navigator interface.
The red wire in the trunk of the Roewe 360 dashcam needs to be connected to the positive terminal of the vehicle battery.
The reason for this design is to prevent the recorder from working properly when the vehicle is turned off.
At the same time, connecting to the positive battery can also ensure that the recorder has enough power to work.
It should be noted that the negative electrode of the vehicle battery should be disconnected before connecting the wire to avoid safety problems such as short circuit.
As an important safety equipment, the vehicle traffic recorder can record accidents and disputes in the process of driving, which is very helpful to protect the rights and interests of the owner.
During the installation process, you should carefully read the instructions, understand the correct wiring method, and install on the premise of ensuring safety. At the same time, we should also pay attention to the storage capacity and use habits of the recorder, clean up the data in the memory card in time, and avoid the recorder can not work properly due to excessive storage data.
The red cable in the trunk of the Roewe 360 dashcam needs to be connected to the ACC power supply of the car.
This is because the ACC power supply of the car only has current output when the key is inserted and the car is turned on, and the tachograph needs to rely on ACC to start and close, to ensure that the tachograph can work normally.
If the ACC power supply of the car is not enough, the red line of the car recorder can also be connected to the normal power supply, but it should be noted that the normal power supply needs to be set up power protection, otherwise it may cause the car battery to discharge. In addition, before wiring, be sure to familiarize yourself with the instruction manual of the tachograph and the circuit diagram of the car to ensure correct wiring and avoid damage to the equipment or the car.
Hello, it is recommended that you refer to the installation instructions of Roewe 360 dashcam or consult professionals for wiring to ensure correct and safe installation. In general, the trunk red wire can be connected to the positive power supply of the vehicle, but the specific connection may vary from model to model. Please pay attention to safety to avoid short circuit or other safety problems.
Because the red line is the power cord of the Roewe 360 tachograph, it needs to be connected to the positive pole of the vehicle to ensure the normal use of the tachograph, if it is connected to the negative pole, it will cause the tachograph to fail to work.
If there is no positive electrode available on the vehicle, you can search for relevant videos or materials, or consult the customer service of Roewe 360 dashcam for more specific wiring methods.
connection method
one
Turn off the car engine.
two
Insert TF card into recorder card slot.
three
Attach the recorder to the original rearview mirror of the car.
four
Plug the car charger into the cigarette lighter, please use the standard car charger.
five
Use the charging extension cable to connect the USB port of the recorder to the car charger.
six
Install the rear camera at the rear of the vehicle, and pay attention to the direction of installation. Wiring can be laid along the roof of the vehicle. After installation, connect the rear plug to the interface of the rear camera of the recorder, and connect the red reverse cable on the extension cable of the rear camera to the positive pole of the reverse lamp.
< br >