This is caused by the residual water vapor between the inside screen and the outside screen of the phone. If the phone is flooded, follow the following steps:
< br >
1. Quickly pull the mobile phone out of the water, unplug the battery, take out the mobile phone card and memory card reason: Once the mobile phone water, the first time must be the battery connection contact water, resulting in power failure or short circuit, so that the mobile phone directly shut down, so we must immediately unplug the battery after taking out the mobile phone, if it causes a long short circuit to burn the motherboard, it is troublesome. Of course, the mobile phone card and memory card should also be taken out. Warning: Many people take out the phone from the water the first thing is to see whether it can be turned on, here must pay attention to must not be turned on. Do not turn on your mobile phone may also save, once the boot, must cause the mobile phone short circuit, there is a great chance of burning the motherboard, the mobile phone is scrapped.
< br >
2. If it is corrosive liquid, it is recommended to flush it with water immediately. Corrosive liquid will definitely corrode the mobile phone. This is of course, especially if there are too many small parts and circuit board chips inside the mobile phone, it is easy to be corroded, and even if such fine parts are corroded in a small place, then the whole machine is difficult to run, so the first time must quickly rinse with water to dilute the corrosive liquid. Make sure the liquid doesn't corrode your phone.
< br >
3. Try to throw water out the reason: The longer the water stays in the phone, the more things are likely to happen, and the more likely the phone will be scrapped. First of all, you can use a rag or toilet paper to suck out the water as much as possible, and it will be much easier to get. Method: Hold the mobile phone to shake hard, but do not shake, the top of the mobile phone up, shake hard in one direction, this is to avoid shaking not only the water can not go out, but also the water in the mobile phone is everywhere, it is not easy to get.
< br >
4. Dry residual moisture reason: electronic products, even if there is only a small amount of moisture in the mobile phone, will have a great impact on the mobile phone, which will affect the operation of the mobile phone, and the short circuit burns the circuit board. Method: A. Use a hair dryer to dry cold air, this is very important, be sure to open the hair dryer cold air, otherwise the hot air may burn the internal parts of the phone. b. Put the mobile phone upright and in a ventilated place. In order to divert the water in the mobile phone, coupled with the breeze sweeping, fully take away the water and avoid leaving too much. c. Many netizens said that after the mobile phone fell into the water, you can take it out and put it into the white rice bag. The water absorption of rice is strong, which can effectively protect your mobile phone from moisture. 4. Take it to after-sales testing reasons: After all, the above methods are some common steps to quickly save the phone, which is not enough to completely clean up some problems inside the phone, and may leave sequelae, so after doing some of the most basic protection, it is recommended not to try to turn on the phone, it is best to take the phone to the after-sales test as soon as possible, so that it is possible to ensure that the phone is not damaged. Tip: The wrong way to do after the phone falls into the water a. choose to turn on the phone the first time out of the water, which is the rhythm of scrapping. b. Use a hair dryer to dry the moisture of the phone, remember to use cold air, absolutely not to the hot air, the high temperature of the hair dryer is likely to burn small parts inside the phone. c. When trying to remove the moisture of the phone, you must not turn the phone off to dry. d. Even if we have done the previous steps, if you are worried about it, you can try to start it, but do not frequently start it, there may be no dry water, it is recommended to go to the after-sales test.
1, of course, the first is to disassemble the whole machine, before you are ready to use the corresponding screwdriver.
< br >
2. When removing the screen, gently separate the small chip connected to the motherboard from the motherboard.
< br >
3. Tear off the card slot sticker under the access card and the access card before removing the metal shield isolation layer.
< br >
4, finally is to take the hair dryer dry, but do not blow on the screen for a long time, such high temperature will destroy the screen, even if the screen has a watermark can also use the phone normally, the water in the screen will generally dry in two days, you will see the watermark inside is getting smaller and smaller.
< br >
5, the motherboard on both sides of the good blow to ensure that there is no moisture residue, the phone and the keys to try to blow out the water.
< br >
6. Finally, put the dismantled mobile phone in a dry and noisy place, it is best to place it for about two days, and then install it.
It is caused by the residual water vapor between the inside screen and the outside screen of the phone. If the phone is flooded, follow the following steps:
< br >
1. Quickly pull the mobile phone out of the water, unplug the battery, take out the mobile phone card and memory card reason: Once the mobile phone water, the first time must be the battery connection contact water, resulting in power failure or short circuit, so that the mobile phone directly shut down, so we must immediately unplug the battery after taking out the mobile phone, if it causes a long short circuit to burn the motherboard, it is troublesome. Of course, the mobile phone card and memory card should also be taken out. Warning: Many people take out the phone from the water the first thing is to see whether it can be turned on, here must pay attention to must not be turned on. Do not turn on your mobile phone may also save, once the boot, must cause the mobile phone short circuit, there is a great chance of burning the motherboard, the mobile phone is scrapped.
< br >
2. If it is corrosive liquid, it is recommended to flush it with water immediately. Corrosive liquid will definitely corrode the mobile phone. This is of course, especially if there are too many small parts and circuit board chips inside the mobile phone, it is easy to be corroded, and even if such fine parts are corroded in a small place, then the whole machine is difficult to run, so the first time must quickly rinse with water to dilute the corrosive liquid. Make sure the liquid doesn't corrode your phone.
< br >
3. Try to throw water out the reason: The longer the water stays in the phone, the more things are likely to happen, and the more likely the phone will be scrapped. First of all, you can use a rag or toilet paper to suck out the water as much as possible, and it will be much easier to get. Method: Hold the mobile phone to shake hard, but do not shake, the top of the mobile phone up, shake hard in one direction, this is to avoid shaking not only the water can not go out, but also the water in the mobile phone is everywhere, it is not easy to get.
< br >
4. Dry residual moisture reason: electronic products, even if there is only a small amount of moisture in the mobile phone, will have a great impact on the mobile phone, which will affect the operation of the mobile phone, and the short circuit burns the circuit board. Method: A. Use a hair dryer to dry cold air, this is very important, be sure to open the hair dryer cold air, otherwise the hot air may burn the internal parts of the phone. b. Put the mobile phone upright and in a ventilated place. In order to divert the water in the mobile phone, coupled with the breeze sweeping, fully take away the water and avoid leaving too much. c. Many netizens said that after the mobile phone fell into the water, you can take it out and put it into the white rice bag. The water absorption of rice is strong, which can effectively protect your mobile phone from moisture. 4. Take it to after-sales testing reasons: After all, the above methods are some common steps to quickly save the phone, which is not enough to completely clean up some problems inside the phone, and may leave sequelae, so after doing some of the most basic protection, it is recommended not to try to turn on the phone, it is best to take the phone to the after-sales test as soon as possible, so that it is possible to ensure that the phone is not damaged. Tip: The wrong way to do after the phone falls into the water a. choose to turn on the phone the first time out of the water, which is the rhythm of scrapping. b. Remember to use cold air when using a hair dryer to dry the moisture of the phone