1. LookThe indicator light. After the SONY Ericsson Bee indicator light changes from red to green, the product is fully charged. The SONY Ericsson Bee is a loudspeaker, a loudspeaker used mainly by teachers to teach. It is divided into two categories, one is waist-mounted and shoulder-mounted teaching loudspeakers, and the other is wireless teaching loudspeakers.
2, first plug the USB charger into the power outlet. Then connect the charging cable to the USB charger and the port of the small bee headset. Finally, when the small bee headset shows a red light, it means that it is being charged, and the charging time is about 1-2 hours. When the headset shows a blue light, it means that charging is complete.
3. Go to the Settings screen and select the notification and status bar. Slide down the screen to find the percentage of battery and open the right slider. After opening, you can open the display percentage function, and you can see the electricity.
4, the use of the product is as follows: The use of function keys: Play/pause key: in the playing state, short press (hold down for less than 1 second, the same below) Play/pause key, long press (hold down for more than 2 seconds, the same below) Select Select the loop playback mode. Press the radio to retrieve the existing station. Forward song selection key: Press the previous song in the playing state, hold down to reduce the volume, and press forward slightly in the radio stateAdjust the frequency, press and hold forward.
5, question 7: SONY Ericsson honeybee loudspeaker used for two weeks, can not afford to charge, change the data line or can not charge if the phone is now no electricity, you need to use the original charger to charge for 30 minutes and then start to try. If you have enough power, try entering engineering mode first to clear the cache and then restart it.
6. The way to use the SONY Ericsson Bee loudspeaker is as follows: Plug the SONY Ericsson Bee loudspeaker into a power outlet and wait for its indicator to light up. Turn on your phone or other audio device and turn the volume to the appropriate size. In mobile phone or other audio SettingsIn the standby Settings, find the Bluetooth option and enable the Bluetooth function. In the Bluetooth search list, locate the SONY Ericsson Bee speaker and click Connect.
First plug the USB charger into the power outlet. Then connect the charging cable to the USB charger and the port of the small bee headset. Finally, when the small bee headset shows a red light, it means that it is being charged, and the charging time is about 1-2 hours. When the headset shows a blue light, it means that charging is complete.
SONY Ericsson S-350 can also play audio via USB stick, so you can play pre-prepared training materials in the training class. In addition, the large battery and power display, so that I do not have to pay too much attention to his power, a charge a week is enough for me to use one or two hours a day. As a productivity tool, the appearance level of the SONY Ericsson S-350 is still very beautiful, usually carried on the waist is not awkward, and listening to music with headphones on the commute is also very good.
The method of connecting the mobile phone to the honeybee is simple: the honeybee loudspeaker turns on, the earphone has a voice prompt, and automatically searches for devices that can be paired. now. Connect the wireless transmission module to the microphone: Connect the wireless transmission module to the microphone interface of the bee.
2, turn on the Bluetooth of the mobile phone, detect the nearby Bluetooth signal to search for the bee. The small bee loudspeaker turns on, the earphone has a voice prompt, and automatically searches for devices that can be paired. At this time, turn on the Bluetooth of the mobile phone, detect the nearby Bluetooth signal, search for the model of the honeybee loudspeaker, click to connect, enter the PIN code, when the mobile phone interface prompts that the connection is successful, the mobile phone and the honeybee loudspeaker are connected, turn on the mobile phone to play music.
3, first turn on the bee electricitySource to put it into standby. Then turn on the power supply of the paired receiver, insert the receiver into the USB port on the computer, and enter the matching state. Finally, hold down the pairing key of the bee and get close to the receiver, and release the pairing key at the same time to complete the FM pairing of the expanded bee.
4, the wireless speaker with a belt buckle on the waist or other position, and then speak into the microphone can be. The small bee wireless speaker also has a LINE IN port that can be used to connect the audio signal output recording of external devices such as electric guitars, keyboards, and synthesizers. The wireless speaker can also connect to a SLR camera or professional cameraMachine, even the DSLR camera to use 5MM microphone cable, professional cameras to use cannon audio cable better.
5, the wireless bee frequency modulation method is very simple, press the set key after the boot, and then adjust the frequency through the two sides of the - key. Let's learn how the Infinitesimal bee tunes. Honeybee loudspeaker why to frequency to frequency means to adjust the frequency to the correct channel, honeybee loudspeaker has a receiver and transmitter, only when they are in the same channel to match successfully, normal use.
1, RODE Rode microphone WirelessgoII II. The RODE microphone WirelessgoII II is a wireless bee receiver that can be used while charging, and the radio effect is very good. The small bee receiver has two types of wireless and wired, the receiver is portable, mobile, small size, loud sound, easy to use.
2, in theory, it is possible, but if it is done in this way, first, it will reduce the service life of the built-in lithium battery, second, it is easy to burn out the circuit systemThird, and most dangerous, the battery may overheat and cause an explosion.
3, can be charged, the correct use of the battery is bee Huawei wireless charging : The first time to use the battery to run out of battery power, fully develop the capacity limit of the battery. Later charges can be charged before they run out. This can effectively extend the battery life.
4, functionally, Rhodes Bee is a digital wireless microphone, through the SERIES III 4GHz digital wireless transmission, 128-BIT encryptionMeter, use the straight line distance to reach the bee Huawei wireless charging 70 meters bee Huawei wireless charging ; Built-in heart-shaped full directional condenser microphone, equipped with intelligent noise reduction chip, can bring high-quality radio effect; And support 3-segment output PAD, automatically adjust the gain of switching microphone output, improve audio quality.
1, Sony Bee does not need electricity, this radio needs a monthCharge it once. Radio, a machine that is constructed of mechanical devices, electronic devices, magnets, etc., that converts radio signals with electricity and can listen to audio signals transmitted by radio stations. Also known as radio, radio, etc. The advent of DSP technology radio marks that the traditional analog radio will gradually withdraw from the historical stage. The digital age of radio has arrived.
2, sony bee fever is because the bee is used for too long, so the circuit board is hot. According to the relevant query, it is good to shut down in time to let it "rest", SONY wireless bee microphone, widely used in radio and television, micro electricityVideo shooting, teaching videos, live interviews and other fields.
3, V. SONY (English bee Huawei wireless charger : SONY Corporation) is a large integrated multinational enterprise group in Japan.
4, the mainland is SONY sold to China's products, there is a warranty, but the price is high (the camera is a high tariff product). Hong Kong licensed goods purchased from Hong Kong, the price is cheap, but there is no warranty in the country. The difference is simple, that is, the sequence identification number of the camera (the nameplate at the bottom of the camera)Up). Bee Huawei Wireless charger You call SONY China Company, give them the serial number, they will tell you what type of product is.
5, can. SONY microphones and cameras can be powered, camera startup bee will also start the recording effect.
6, small bee d11 is a small bee microphone, and small bee d12 is a sister model of small bee d11, it is a microphone, both can meet the needs of different users.
1, First of all, after the third generation of the Chinese Taiwan bee loudspeaker is turned on, there will be a voice prompt in the headset, and it will automatically search for the equipment that can be matched. Secondly, turn on the Bluetooth of the mobile phone, detect the nearby Bluetooth signal, search for the model of the small bee speaker, select the connection, and enter the PIN code (the default is 0000). Then when the mobile phone interface prompts that the connection is successful, the phone and the small bee loudspeaker are connected.
2. Plug the receiver into the amplifier audio input port and turn on the wireless microphone power. Make sure the microphone and receiver signal are connected properly. Turn on the power and adjust the volume to the appropriate height to hear the sound transmitted by the microphone.
3. The method of using the loudspeaker is as follows: The music playback function needs to insert the TF music storage card, find the storage card slot of the loudspeaker, and the place where the picture is circled. Insert the TF card. Turn on the power switch and play music immediately. Amplification function: Insert the microphone into the microphone jack to achieve real-time amplification function. The audio input jack is connected to a computer audio cable to output audio as a speaker.
4, the first ten degrees of small bee wireless microphone use method to prepare a normal small bee amplificationA surname Next, insert the microphone that came with the bee into the correct microphone jack. Finally, the small bee is hung on the waist, the microphone is hung on the ear, the opening key is turned on, the sound size is adjusted, and then the amplification function can be used normally.
5, small bee wireless speaker by the waist buckle, audio line, transmitter, receiver, collar microphone and other parts of the composition, when using, first press the switch button, the indicator turns blue to start. On the LCD display, you can switch the volume and channel, press the set key to switch the channel and volume, and the left and right signal key and - key can raise or lowerReduce the volume and adjust the channel, set the appropriate volume and frequency band.
6, first of all, insert the receiver of the wireless microphone into the amplifier audio input port and turn on the wireless microphone power supply, then ensure that the microphone and the receiver signal connection is normal, and finally open the small bee power supply, adjust the volume to the appropriate height, in order to hear the sound transmitted by the microphone. Honeybee loudspeakers and wireless microphones convert sound waves into electrical signals, and then use high-frequency radio waves to emit them, and the receiving end receives demodulation and amplification to push the speaker to work.