1. Charging the earphone body Put the Rambler tws2 earphone into the charging box Rambler wireless headset box charge for how long , note the left and right corresponding. When the Rambler tws2 headset indicator lights red How long is the Rambler wireless headset case charged , the headset is charging. After 5 hours of charging How long the Rambler wireless headset box is charged , the Rambler tws2 headset is fully charged, the indicator light is blue, and the three white lights of the charging case can charge the headset 3 times.
2. Use the Rambler tws2 headset normallyThe indicator will slowly flash a blue light, and if the headset's battery is less than 10%, the indicator will light red until the battery runs out. When the Rambler tws2 headset is in the charging state, the headset indicator light will be steady red. When the Rambler tws2 headset is fully charged, the headset indicator lights up blue.
3. When the Rambler Bluetooth is charging, the light will be on, and the blue light will be on. The indicator light of the Rambler tws2 headset is located at the raised position on the edge of the headset, and the indicator light of the headset can reflect the headset battery status and Bluetooth status.
The Rambler TWS5 headphones have a total battery life of 32 hours in the charging case, and the headphones themselves can play music for eight hours. The charging case provides an additional charging opportunity for the headset, which can be charged up to 3 times in total, ensuring that the user has enough charge when going out. When the charging case runs out of power, it needs to be charged.
Charging The charging box The charging port of the Rambler tws5 headset is at the bottom of the box, and you can see that the charging port is microUSB charging port. The earphone comes with a micro USB charging cable. Use the smaller end of the charging cable to plug into the charging port of the charging case, and connect the larger end of the charging cable to the USB power supply or connect to the USB charging connector and plug into the power supply.
Charge the earphone Open the charging case of the Rambler tws5 earphone and take out the earphone. You can see that there is a magnetic needle at the bottom of the groove in the charging case that contacts the earphone. The charging case charges the earphone through the magnetic needle. Look at the main body of the headset, both sides of the bottom of the headset have a concave charging interface, which is and charging boxWhere the magnetic needle touches.
1, the Rambler TWS3 headset is equipped with a charging box How long the Rambler wireless headset box is charged , which can be resupplied when the headset is short of power, but ultimately it must be connected to the power supply for charging. So how to charge the headset and charging case How long does the Rambler wireless headset case charge ? Follow me around. Earphone chargingThe reasons why the headset is full but not charged are as follows: The Bluetooth headset battery is exhausted and overused, resulting in the battery being self-protected while charging. The earphones are not in place. You are advised to adjust the position and reinstall it. The charging port of the charging bin (or headset) is in poor contact.
In this case, the other headset may not be charged, or the other headset has a problem, there is a fault. Solution: You can try to put the headset without power into the ear compartment again, and adjust the position until the two electrode buttons of the headset and the headset compartment coincide. Take it out again after a period of time, if there is still no electricity is a malfunction of the headset.Need to contact customer service to repair or return.
If the headset is not used for a long time, it is recommended to charge for more than 10 minutes before activating the headset; 2 Clean earphone or charging case contacts with alcohol; 3 Put the headset into the box and charge the charging box for more than 10min; /4 Put the headset into the charging case and open the cover, long press the function button for 16 seconds, and let go until the indicator light outside the charging case flashes. Then put the left and right headphones into the charging case respectively to confirm whether the indicator light inside the case can be turned on. If it can be turned on, the headset will return to normal.
can be used separately. The Rambler wireless Bluetooth headset is supported by two headset pointsOpen to use, while the earphone is powered off, the earphone can still play music normally, you can put the earphone without power back to the charging bin to charge, after full charge can be used normally.