First remove the six screws behind the partition, slowly knock the edge with the word, pinch the protrusion with the needle nose pliers, there are four such clips, all can be removed.
Removing the battery holding screws with an ordinary wrench is not complicated, but it is very expensiveTime. After removing the battery fasteners, the cables connecting the positive and negative terminals of the battery also need to be removed separately before the old battery can be removed. The new battery is placed in order to confirm the position of the positive and negative terminals, so that the cable can be correctly connected to the remarks, to avoid accidents caused by improper installation and connection. After the new battery is installed on site, the vehicle can resume normal use.
Disassemble directly. Remove the cover of the SiHAO e10x wireless charging module, and use a grid for copper coating on the other side in the position without charging coil. The corresponding wireless charging coil area is grid-shaped with copper, and the module is removed and the rubber pad is torn.
First remove the free light withoutClinker cushion for wire charger. Next, unscrew the four screws. Finally unplug the power plug, you can remove the wireless charger.
First of all, you need to prepare some tools to turn off the ignition switch of the car, so as not to short circuit or cause other safety problems. Second, you need to remove the shell of the car charger, after removing the shell, you can access the internal structure of the car charger, according to the need, you can clean or replace the internal circuit board, capacitors, resistors and other parts, be careful when disassembling, do not damage any parts.
First take the air conditioning panel apart, then unplug the back harness, in accordance withRemove the large screen and pull out the back harness, and then remove the screws of the host, and install it back in order. The center console can be roughly divided into two parts, the above vehicle multimedia system, the following is the air conditioning control area, of course, there will be a reverse design of the model, but a few.
1, green magnetic wireless charging mobile power disassemble the body shell, the edge of the buckle sealPretend. The PCB board is fixed with screws, the wireless charging coil is fixed on the battery core, and is covered with foam protection. A thermistor is fixed on one side for temperature monitoring. Take out the PCB board and electric core, the body shell is affixed with protective foam, the corresponding circuit board and electric core junction is provided with an isolation board.
2, Green Link MFi certified 10000mAh two-way fast charge mobile power supply This mobile power supply stands out with its exquisite design. It uses PC flame-retardant material, the shell lines are rounded, the laser engraving texture adds a touch of science and technology, and the UGREEN brand Logo stands proudly. There are four leds on the frontThe indicator light is clear and intuitive, the power button on the side is convenient to operate, and the Lightning output line is cleverly designed and stored in the internal cable slot, which is practical and neat.
3, the green magnetic wireless charging technology is derived from Apple's MagSafe wireless charging for iPhone 12. Unlike ordinary wireless charging, thanks to the magnet ring added inside the iPhone 12, the charger can be closely fitted with the phone, and there is no need to worry about not being aligned, which is more convenient.
4, the power absorption treasure is the magnetic charging treasure and magnetic chargingDevice, such as green link's magnetic charging treasure is good. Green Link Three-in-one MagSafe magnetic wireless charging Bank is a three-in-one MagSafe magnetic wireless charging bank, using Apple's ATL battery, providing a strong magnetic design. Of course, the wireless cable dual mode fast charging design, plus can be transformed into a mobile phone stand, used to charge while chasing the drama. Wireless charging provides 10W, 5W, 5W charging.
5, Green link magnetic wireless charging bank 20W fast charge for you to seek more compatibility, Green Link this charging bank to meet the needs of the people. A new choice of domestic brands, designed for domesticMobile phone brand building...) This charging treasure sets magnetic mobile power and wireless charging in one, with discharge and charge, strong compatibility, can provide charging services for 99% of mobile phones, whether it is Apple, Huawei, Xiaomi or Samsung, can easily cope with.
6, Green Link this charging bank pays attention to the seamless fit with the iPhone. The MiniCell battery is the same material system as the iPhone battery, ensuring safety and durability. Built-in 9 powerful magnetic cores, accurately match the iPhone 12-14 series, to achieve a convenient experience. Its exterior design is fashionable and adoptedWith spray PU feel paint, amiens electroplating frame, light and portable, only 2/3 of the volume of iPhone 14, more comfortable to use.
BYD Han's wireless charging switch is located in the front of the central armrest. Byd Han's length, width and height are 4950*1890*1490mm, and the wheelbase of the body reaches 2940mm, which is expected to be a medium and large car. In terms of configuration, BYD Han is equipped with a wealth of configurations, such as ACC adaptive cruise, electric suction doorHead-up display, parallel assistance, lane keeping assistance, and inductive opening of suitcases.
The mobile phone wireless charging area of BYD Han EV model is located in the front of the central armrest storage box of the center console. When the vehicle power gear is in the "OK" gear, the phone can be placed on the non-slip rubber mat in the wireless charging area, with the phone screen facing up. In this position, the phone will automatically start wireless charging, and the charging icon will be displayed on the multimedia UI interface.
Yes. Byd Han has wireless charging function, in the armrest box in front of the space, as long as the mobile phone supports wireless charging, put on it.
What do you want to ask is that mate50 can not be charged wirelessly on BYD Han? Solution: First of all, the BYD car wireless charger is unplugged in the car. Second, plug the wireless charger back into the car. Finally, the phone can be charged by placing it in the wireless charging area.
Yes. Byd Han dm wireless charging Settings are as follows: BYD Han EV mobile phone wireless charging area is located in the front of the central armrest storage box in the center console, when the vehicle power gear is in the "OK" stop, the mobile phone is placed on the non-slip rubber mat in the wireless charging area, the mobile phone screen faces up, the mobile phone automatically entersUrgent need.
2, when using wireless charging, make sure that there is no other object on the WPC panel, only the phone. You also need to turn on the intelligent interconnection NFC and wireless mobile phone charging function inside the central control setting, and then confirm the wireless charging function through the mobile phone operation, and finally put the mobile phone in the center of the charging board to start charging. It should be noted that at the current level of technology, wireless charging efficiency is not high, and there is a serious problem of heat generation.
3. Make sure that there are no objects on the surface of the WPC. 2 Click Function -- Settings -- Intelligent Connection on the central display-- NFC and wireless phone charging. 3 Tap mobile phone wireless charging to activate/deactivate the function. 4 Place the phone in the center of the charging pad. After the charging of Lynk & Co 02 wireless mobile phone starts, it will be displayed at the bottom right of the screen, and stop charging when the phone is full. Keep metal objects away from the charging pad when charging, as metal objects may overheat the pad.
4, the opening method of Lynk & Co wireless charging is: click the function button on the central display; Swipe down the page to find Settings and click; Click Smart Internet to turn on nfc and wireless charging. Take the 2020 Lynk & Co as an example, which is a compact suv with a bodyThe length, width and height are: 4592mm, 1879mm, 1628mm, and the tank volume is 52l.
5, click the mobile phone wireless charging, activate/disable the function. Place the phone in the center of the charging pad. It will be displayed at the bottom right of the screen when it starts charging, and will stop charging when the phone is fully charged. When charging, make sure that metal objects are kept away from the charging pad, which may overheat the pad. Make sure credit cards or other magnetic objects are kept away from the charging pad to avoid erasing the magnetic information.
6, using the wireless charging function of Lynk & Co 02 is very simple. First, make sure the WPC surface is clean and freeClutter. Then, on the central display, select functions, Settings, Smart Connectivity, NFC and wireless phone charging in turn. Then, tap the phone's wireless charging option to activate the feature. Finally, place the phone in the center of the charging pad to start charging. During the charging process, the charging status will be displayed at the bottom right of the screen. When the phone is fully charged, the charging will automatically stop.
1, mate30 can not remove the wireless charging module. Mate30 series smartphones areIt supports wireless charging, and the wireless charging module is an electronic device fixed on the mobile phone motherboard, and it is not recommended that users disassemble it themselves. Because removing the wireless charging module may cause the phone to lose its wireless charging function, and this change may violate the warranty regulations, causing irreversible physical damage.
2. Destructive disassembly is the mainstream disassembly method for material recycling at present [3]. 80% of the components in used mobile phones can be reused [4]. Destructive disassembly will damage some well-functioning components and cause e-waste pollution, especially the destruction of water ecology and soil ecology [5]. automateLossless disassembly is the trend of disposing of used smart phones, and a better understanding of the internal structure and connection of mobile phones is the basis of fully automated lossless disassembly [6].
3, first of all, you need to shut down the iphonex phone completely, prepare the screwdriver, and remove the bottom two screws of the screen. Secondly, you need to remove the screen with a card and remove the metal sheet screws of the old wireless charging module. Finally, remove the old wireless charging module and replace it with a new wireless charging module.
4, directly disassemble. Remove the cover of SiHAO e10x wireless charging module and place the other side in the position of no charging coilThe coating of copper uses grid form. The corresponding wireless charging coil area is grid-shaped with copper, and the module is removed and the rubber pad is torn.