1, the general family network planning and design is very experienced, designed and installed a lot of large villa network system, for the general small and medium-sized apartment has also been studied in detail, this article is only used as a general family network planning wiring guide.
2, set up a home broadband network so that the study, living room, the master bedroom of the three computers share a broadband signal, which can save Internet access feesWith, it can realize the networking and resource sharing between computers. Set up a home audio network in the living room to install a surround sound playback system, and can send different signals to the kitchen, dining room, bathroom and living room.
3, the network requirements of the second bedroom computer In order to meet the network requirements of the second bedroom computer, it is recommended that you pull a network cable directly from the living room to the second bedroom. This can ensure the stability and speed of the network signal. Laying the Spare network cable You are advised to lay two network cables at a time between the living room and the bedroom, one for Internet access and the other for backup. This can ensure the stability of the network signal and spare linesRoad reliability.
1, yes, the two kinds of lines are insulated, and the network cable you will not use for a few years, it is not eliminated by WIFI, it is to change the faster super 6 type of line, and the current network cable is abandoned in these years.
2, the network wiring is different from the home decoration layout wire, the installation place is in the floor, the wall, through the PVC pipe and the end to the bottom box. However, the network cable to receive information belongs to one network cable and cannot be in the middleIn order to continue, we must go all the way to the end.
3, the network wiring in the home is similar to the wire wiring, which needs to be hidden in the floor and wall, and is laid to the type 86 bottom box through PVC pipe. The network cable must be laid from the information point to the RJ45 information module of the terminal without a connector. It is not difficult for ordinary construction teams to master the basic wiring skills, but the difficulty lies in the correct installation of the information module.
4, the network wiring of the home improvement project is actually some of the same as the construction method of wire wiring, which is concealed in the floor and wall, after PVC pipe and end in the bottom box of 86. But a network cable is a point of informationThe network cable cannot be renewed in the middle. Go through the line to the end. These are not difficult for the general construction team, the difficult is how to install the interface module at the beginning and end of the network cable.
1, the socket installation has A variety of skills: A wall concealed: 86 iron square box embedded in the wall, only the appearance of the board. B Wall mounting: The box protrudes the wall, the panel is installed on the box, and the line slot is matched with the box. C Screen hidden installation: wiring and installation of bottom box and socket panel in the cable trough of the screen. D Ground concealed: iron square box embedded in the ground, AnnInstall waterproof floor sockets. Switch types There are many kinds of switches with different functions. There are lamp switch, access control switch, doorbell button and background music switch.
2. Prepare the switch socket (that is, the socket with the switch). The following figure shows that the red live wire connects to L, the yellow ground wire connects to L1, and the blue neutral wire connects to L2. The firewire jumper on the switch jumps to the L on the socket. L2 on the socket connects to the light control cable. The neutral line of the lamp line comes out to connect the switch.
3, install the bottom box fixing skills first take apart the cover covered by the front of the socket or switch, clean up the bottom box, and put all the debrisClean it out to prevent affecting the installation process. Next you can secure the bottom box with screws. Insert the screw into the screw hole in the bottom box and tighten it with a screwdriver to secure it to the wall.
4. If it is a control lighting, install it as follows: the live wire of the power cable is connected to the L interface of the socket, and a power cable is connected to the first wiring of the switch, the neutral wire of the power cable is directly connected to the N interface, the ground wire is connected to the E interface, and the outlet wire of the lighting cable is connected to the second or third wiring.
5, when installing, should choose a height of 3 ~ 5m from the ground, if roomSurface 86 bottom box size '> Surface 86 bottom box size
1, the size of the bottom box is generally 86mm*86mm86 bottom box wireless charge , the installation hole distance is 60mm, and the diameter of the connected wire tube is 25mm. The front of the bottom box is generally 86mm86mm square (the size of individual products varies slightly due to the appearance design). On the basis of the type 86 switch, it is derived from the 86 bottom box wireless charger Type 146 (146mm86mm) and moreSwitch receptacle for joint mounting. 86 box is a specification of a junction box and an industry standard in electrical decoration.
2, mm ×86 mm ×18 mm. The type 86 bottom box refers to the electrician's bottom box, which is a common junction box with a width, height and depth of 86 mm. Since the 86 panel is usually only a household switch socket, information socket and other panels, because the length and width are 86 mm, it is commonly known as the 86 panel. In home decoration, the bottom box is a common decoration accessories, mainly used for the installation of electrical equipment such as switch sockets.
3, open box and dark boxThe main reason for the different box sizes is that they are installed differently. The size of the bottom box is different from the size of the bottom box, the size of the bottom box is equivalent to the panel size, and the size of the bottom box is slightly smaller than the panel size of a few millimeters. In addition, the depth (that is, the thickness) of the hidden bottom box is 1 to 2 cm deeper than the open bottom box.
4, this is a type 86 open-mounted bottom box, the depth of the box is generally about 32mm, the bottom has a number of groups of screw eyes, and wired slot interface. The depth of hidden installation is generally 40~50mm, the bottom of the box is generally no screw eyes, no cable slot interface, but there are multiple pipe holes.
If there are two or more 86 bottom boxes installed next to each other, the 86 link bottom box must be used. You don't have that problem with a button-down box. Unless the fastener made by the manufacturer is faulty. Since the problem occurs, the remedy: dig the wall, remove the position, correct the bottom box position.
The ap panel needs a bottom box. AP panel: Looks similar to a regular wall network outlet, but it can emit wireless signals. Emit nothing in every roomLine signal, naturally there is no wifi dead corner. Therefore, if we want to use this networking method, the first step we need to do is to reserve network cables in every room.
Use a screwdriver to remove the panel of the type 86 network connection on the wall. (If no box cover is available, you can ignore it.) Use network cable pliers to make a RJ45 connector of the network cable arranged on the wall, and connect it to the POE cable port on the rear of the AP on the panel. Align the screw hole on the AP with the screw hole on the cassette, and then install the screw on it to secure. Secure the AP shell cover and complete the installation. Traditional aps are mostly desktop.
Method/Step 4 The results of the speed measurement are not bad, it seems that we are not connected to the wrong line. Then we'll install the panel AP. It is necessary to remove the front cover of the panel AP before installation. The installation method is the same as that of the usual 86 power socket. Install each screw and cover the panel. And that's it. Isn't that easy? Look at the method/Step 5 Well, speaking of which, our smart panel AP installation process is finished.
Step 1: Remove the cover and remove the cover from the panel with a screwdriver. Step 2: Connect the wire, connect the 220V wire, network cable and telephone line to the surfaceOn the specified interface on the back of the board, ensure that the connection is secure (Note: when connecting the 220V cable, disconnect the power supply before connecting it to avoid electric shock accidents) Step 3: Install the screws, remove the screws from the packaging box, put the socket in the bottom box, adjust the fixing screws in the bottom box, and tighten the screw ratio.