1, the method of making wireless charger is as follows: Attach the module to the place where the MicroUSB interface is compared. Connect the MicroUSB or Lightning port on the module to your phone. ifThere is double-sided tape on the receiver, which can be glued directly to the back of the phone. If it doesn't come with it, you have to figure it out yourself. Choose the most suitable position, be careful not to let the part of the connection line have the phenomenon of warping.
2, soldering iron, copper wire, resistor, transistor, capacitor. That will do. So wireless charging is simple. But I suggest you don't do it yourself. It's all special materials. If you do it for fun, just make an oscillating circuit.
3, one of the self-wound coil is connected to the charging circuit, 555 output pin (the third pin) is connected to an output tube (oneself at will,But to the high-frequency power tube) the output tube is linked to the self-winding coil, and the connected two coils are close (about 1 cm or so there is a very sufficient charging current). The efficiency of this circuit is very low, because there is only half a wave peak high frequency so the loss is relatively large, but the principle is quite simple and easy to produce.
4, no magnet in the wireless charger. If you place an energized wire on a magnetic compass, you can see that these currents also produce a magnetic field. If you use a moving magnet instead of an alternating current wire, you're ready. The production of varying currents in wiresReady to use, convenient and fast.
2, you can buy a wireless charging receiver, stick it on the back of the mobile phone or insert the mobile phone charging port, the advantage of this method is that the cost is low, there is no need to replace the mobile phone or dismantle the internal phone, the disadvantage is that it may affect the beauty and feel of the mobile phone, as well as increase the wear and tear of the charging port.
3, to change the ordinary mobile phone to wireless charging, usually need to use a wireless charging receiver and corresponding modification tools. However, please note that this modification may damage the phone or void the warranty, so it is recommended to modify the wireless charger trong> Understand the risks and consequences before proceeding. Wireless charging technology, which allows users to charge devices without plugging in a cable, has become increasingly popular in recent years. However, not all phones support wireless charging natively.
4. Open the Settings of the Huawei mobile phone. Click the "Battery" option to enter. On the battery page, click the "Charging Settings" option to enter. On the Charging Settings page, turn on Wireless Reverse Charging. Finally, wireless charging can be successfully connected.
1,First, cut the USB charging cable into two sections not far from the two ports. Use scissors to separate the tail glue of the two wires into a section to screen and then cut off the green wire with a double bottom line. Use hot glue to attach the magnet to the charger. Wrap the wires in the USB with tinfoil. Then wrap the wire with copper wire to How to modify wireless charging they roll up. The USB cable with the copper wire rolled up is then wrapped in electrical tape.
2, self-made wireless charger 1: External module installation steps Stick the module in the place from the MicroUSB interface comparison. Steps toThe MicroUSB or Lightning port on the module connects to the phone. Steps If there is double-sided tape on the receiver How to modify wireless charging , you can directly glue it to the back of the phone. If there is no attached then how to modify wireless charging , we must find a way to ourselves. Step to select the most appropriate position, be careful not to let the part of the connection line warped phenomenon.
3, first of all, to understand the working principle of wireless charging. The wireless charging system is mainly composed of two parts: the transmitter (usually putOn the charging pad or charging dock) and receiver (installed inside the phone). The transmitter generates a magnetic field, which the receiver converts into electricity via induction to charge the phone's battery. To add wireless charging to a regular phone, the most critical thing is to install a wireless charging receiver.
1, conclusion: Meizu MX2 originally does not support wireless charging, but through the modification of enthusiasts, it can indeed achieve this function. However, this modificationThe method is not official and has certain limitations. Although the Meizu MX2 is not officially equipped with wireless charging function, some mobile phone enthusiasts have achieved its transformation through innovative means.
2, usage is as follows: Ensure that the Meizu 20Pro and wireless charger are in normal working condition, and the charger is connected to the power supply. Find the wireless charging receiving area on the back of the Meizu 20Pro. This area will be in the center or top of the back of the phone. Place the wireless charger on a flat surface, ensuring that the charger is aligned with the wireless charging receiving area of the Meizu 20Pro.
3. First, connect the Meizu wireless charger to the power supply and place it on a flat desktop. Second, remove the shell of the Meizu 20pro phone. Finally, put the center of the back of the phone on the wireless charger, and you can complete the wireless charging of Meizu 20pro.