1, check whether the phone is overheated wireless charger for a few seconds to stop , it is recommended to charge under good heat dissipation conditions. Check whether the wireless charger indicator light is on normally Stop the wireless charger after a few seconds , and check whether the connection between the charging base, data cable, charger and power supply is in bad contact, it is recommended to re-pullInsert it once. Verify that the center of the phone is placed in the center of the wireless charging base during charging, and remove other items (such as bus passes, metals, etc.) between the device and the wireless charger.
2, because some mobile phone protective cover is too thick, or the material of the mobile phone protective cover may affect the recognition function of the mobile phone wireless charger, it is recommended that you take off the mobile phone protective cover and try again. 4, please check whether there are other items between the mobile phone and the wireless charger. Wireless charging converts electrical energy into magnetic energy for transmission to the phone, and if the magnetic energy is interfered with, charging will be affected.
3, chargeCheck that the phone is facing the center of the wireless charging pad. If it is not, it may not charge properly. If there are obstacles between the charging pad and the phone, such as keys, coins, etc., it will affect the charging effect and they need to be removed. The phone case is too thick thick protective case may affect the charging effect, try to take down the phone case and then charge.
4, please avoid mobile phone displacement, position deviation will lead to no charging. Please check whether you are using wired charging. If wired charging and wireless charging are used at the same time, wired charging will be preferred. If the above method does notTo solve your problem, you are advised to back up your data in advance and go to a nearby Huawei customer service center with your mobile phone, charger, data cable, and purchase certificate.
5, the method that can be taken in this case is wireless charger charge for a few seconds to stop : Determine the phone and wireless charger compatibility, check the charger and power adapter, check the alignment between the wireless charger and the phone. Make sure the phone is compatible with the wireless charger: Make sure the wireless charger stops charging after a few seconds your phone supports the wireless charging function whileThere are problems such as poor contact of the charging port and loose charging cable, which may lead to unstable wireless charging.
The reason for the automatic disconnect of wireless charging in a few seconds: the first is that the wireless charging coil is damaged, resulting in the current of the mobile phone can not be transmitted normally inside the coil to the battery of the mobile phone during wireless charging. The second is that the position of Apple's wireless charging is not aligned with the position of the phone, and the position of Apple's wireless charging coil is in the center position behind the Apple body.
Hello, if you use a wireless charger, there is always an intermittent charging prompt tone, which should be absent on the back of your phoneAccurately placed on the wireless charging contact surface, there may be your phone case affected wireless charging, you can remove the phone case and try again.
The reasons for this situation are as follows: First, the magnetic phone case will interfere with the wireless charging coil of the phone, affecting the charging effect. The wireless charging coil of the mobile phone needs to be accurately aligned with the coil of the charger to achieve charging, and the magnetic phone case will change the shape and weight of the mobile phone, making the wireless charging coil and the coil of the charger cannot be accurately aligned, resulting in poor charging effect.
1, hello, if you use a wireless charger, there is always an intermittent charging prompt tone, it should be that the back of your phone is not accurately placed on the wireless charging contact surface, and it may be that your phone case affects wireless charging, you can remove the phone case and try again.
2, if the iPhone wireless charging suddenly does not charge, it may be because sometimes unpredictable errors occur in the update of the iOS system, which will cause problems with the wireless charging function, usually as long as the restart can be solved. Removing the iPhone case sometimesWaiting for the iPhone protective case is too thick will also lead to wireless charging, then you can try to remove the iPhone protective case, and then put back on the wireless charging board to charge.
3, it is estimated that the charger output power is insufficient automatic protection stop output. Although the original charger of the mobile phone is 5V1A, the actual input can be more than 1A, and the 5V2A charger can be used. If the wireless charger output power is only 5W, it is not enough. Only the money spent on the wireless charger, and no input and output parameters, is not matched. Bluetooth headset power is too small, for comparison can not explain the problem, but can explain wireless chargingThe device is available.
4, it may be that the charging interface of your phone is in poor contact, resulting in the best is to replace a new one outside.
5, restart the phone: When the phone has such a problem, we can force to hold down the power button, about 20s, the phone can automatically restart, at this time we take a look. Replace the wireless charger: When our mobile phone has such a situation, it is likely that there is a problem with the charger, you can replace a wireless charger to try.
1, the distance between the charger and the phone is too far. Xiaomi wireless charger needs to fit with the phone to charge normally, if the distance is too far, the light will always flash. The charger port is loose. The interface of the wireless charger must be correctly inserted into the power socket, and if the interface is loose, the light will always flash. There is a problem with the charger.
2, hello, if you use a wireless charger, there is always an on-off chargeThe electric prompt sound should be that the back of your phone is not accurately placed on the wireless charging contact surface, and it may be that your phone case affects wireless charging, you can remove the phone case and try again.
3, wireless charging a few seconds will automatically disconnect the reason: the first is the wireless charging coil is damaged, resulting in the mobile phone in the wireless charging when the current can not be normally transmitted inside the coil to the mobile phone battery. The second is that the position of Apple's wireless charging is not aligned with the position of the phone, and the position of Apple's wireless charging coil is in the center position behind the Apple body.
4, charge the phone, see ifCan be normally full (that is 100%) if the use of mobile phone charger to charge the mobile phone can be normally full, it indicates that there is a fault inside the wireless charger, if the use of mobile phone charger can not be often full, this problem, in the case of the charger, charging data line, mobile phone tail plug are normal, the problem may be, The charging control circuit on the main board of the mobile phone is faulty.
5, at a certain stage of charging, the chip switches the charging mode and the current is small, resulting in interference, so that the wireless charger can not correctly receive the signal of the mobile phone, simply put, the chargerCan't confirm if the phone is still there. The situation of one charge and one stop sometimes turns into a direct disconnect and no longer charging. This problem is inherent in different phones, and new wireless chargers have generally solved this kind of compatibility problem.
6, can be out of power, the protection state is blinking. When the millet wireless charger, millet wireless charger (universal fast charging version) LED light status is green flashing, millet wireless charger is in the error and protection stage. At this time, you should pay attention to whether there is a metal object placed on the wireless charger, please remove it and charge it again. Just give it a second. It's not in the right place. I got metalForeign objects, automatic protection Settings.
1, hello, if you use a wireless charger, there is always an intermittent charging prompt tone, it should be that the back of your phone is not accurately placed on the wireless charging contact surface, and it may be that your phone case affects wireless charging, you can remove the phone case and try again.
2, if the iPhone wireless charging suddenly does not charge, it may be because sometimes the iOS system update has unpredictable errors, willProblems caused by wireless charging function can usually be solved as long as the restart. Remove the iPhone case Sometimes the iPhone case is too thick will also lead to wireless charging, then you can try to remove the iPhone case, and then put back on the wireless charging board to charge.
3, it is estimated that the charger output power is insufficient automatic protection stop output. Although the original charger of the mobile phone is 5V1A, the actual input can be more than 1A, and the 5V2A charger can be used. If the wireless charger output power is only 5W, it is not enough. Only the money spent on the wireless charger, and no inputThe output parameter is not matched. The power of the Bluetooth headset is too small to explain the problem for comparison, but it can explain that the wireless charger is available.
4, charge the mobile phone to see if it can be normally full (that is, 100%) if you use the original charger of the mobile phone to charge the mobile phone can be normally full, it indicates that there is a fault inside the wireless charger, if the original charger of the mobile phone can not be often full, this problem, in the case of the charger, charging data line, mobile phone tail plug are normal, The problem may be that the charging control circuit on the main board of the mobile phone is faulty.
5It may be that the charging interface of your phone is in poor contact, which is best to replace it with a new one outside.
High temperature High temperature protection or there is a metal foreign body between the mobile phone and the charging bank, or the charging bank or the mobile phone is broken.
The mobile power supply is a charging device produced by a third party, so it will be compatible with the mobile phone, the official recommendation is to makeUse the original charger to charge the phone, which can better protect the service life of the phone and battery. If the purchased third-party mobile power supply cannot be used, it may be caused by compatibility problems, please contact the dealer.
The power off after a charging treasure is generally caused by: insufficient output of the charging treasure, bad contact, and unstable mobile phones or charging treasure chips.
This is because the mobile power supply enters the charging protection state. When charging the mobile phone, overcharge or high voltage will make the mobile power into the charging protection state, this time to charge the mobile power is not charged.
is the reason for the data cable, with the original data cable of the mobile phone, there will be such a problem, should use the original data cable of the charging treasure, because the USB port of the charging treasure may be incompatible with your data cable. Maybe the connection didn't make good contact, causing a leak. Or there is a problem with the charging bank, the positive and negative output is reversed, and the problem can not be used for the time being. The phone may be infected with a virus. It's consuming more power.