1, the distance between the charger and the phone is too far. milletThe wireless charger needs to fit with the mobile phone to charge normally Xiaomi wireless fast charging , if the distance is too far Xiaomi wireless fast charging , the light will always flash. The charger port is loose. The interface of the millet wireless charger must be correctly inserted into the power socket Millet wireless fast charging , if the interface is loose Millet wireless fast charging , the light will always flash. There is a problem with the charger.
2, 3, wireless charging a few seconds will automatically disconnect the reason: the first is the wireless charging coil is damaged, resulting in the mobile phone in the wireless charging when the current can not be normally transmitted inside the coil to the mobile phone battery. The second is that Apple's wireless charging position is not aligned with the position of the phone,Apple's wireless charging coil is located in the center of the back of the Apple body. 4, charge the mobile phone to see if it can be normally full (that is, 100%) if you use the original charger of the mobile phone to charge the mobile phone can be normally full, it indicates that there is a fault inside the wireless charger, if the original charger of the mobile phone can not be often full, this problem, in the case of the charger, charging data line, mobile phone tail plug are normal, The problem may be that the charging control circuit on the main board of the mobile phone is faulty. 5, in the charging to a certain stage, the chip switch chargingWhen the mode and current are large, the interference generated makes the wireless charger unable to correctly receive the signal of the phone, which is simply that the charger cannot confirm whether the phone is still in. The situation of one charge and one stop sometimes turns into a direct disconnect and no longer charging. This problem is inherent in different phones, and new wireless chargers have generally solved this kind of compatibility problem. 1, millet wireless car charger can only tighten a certain total width of the mobile phone, if the owner of the mobile phone is relatively narrow, it is likely to clamp tooLoose, which leads to intermittent charging. It can replace the small wireless network car charger, and it can also put the mobile phone shell on the mobile phone shell to try whether the mobile phone can tighten up a little. It may be that the iron clamp force of the car charger itself is insufficient, or the product quality problem of the car charger itself. 2, millet wireless car charger can only tighten a certain width of the mobile phone, if the rider's mobile phone is relatively narrow, it may not be tight, resulting in intermittent charging. You can replace a small wireless car charger, you can also put a phone case on the phone, and try to tighten the phone a little. Maybe it's the clamping force of the car charger itselfYes, or there is a quality problem with the car charger itself. 3, please use the original charger to charge the phone, or check whether the charging interface is properly connected. It may also be the cause of unstable mains voltage, please replace the charging environment, or replace it to the computer usb charging try you to shut down and charge, check whether it can be charged normally. If possible, please replace a cable or charger for charging. If it does not charge normally, please go to your nearby repair point to check. 4, the mobile phone does not support wireless charging. There is a foreign body, metal or mobile phone cover on the wireless car charger bracketXiaomi wireless charger has a foreign body detection function, if the charger encounters a metal foreign body near, will automatically power off, and continue to flash the green light, so check whether there is a metal object around the charger. 5, the power adapter is faulty or the charging line is damaged, you can try to replace the power adapter and the charging line to see if there is still a problem. Poor contact inside the charging port or battery aging will also lead to intermittent charging. If the problem persists after the power adapter and charging cable are replaced, you may need to replace the mainboard or repair the charging portThe wire charger will automatically charge the phone after it is fully charged... '> Friends who have not used the millet wireless charger, the millet wireless charger will automatically charge the mobile phone. 1, full will definitely stop Millet wireless fast charging , and the battery also with a protective plate Millet wireless fast charging , full Millet wireless fast charging can no longer be charged. Mobile phone automatic power off principle Millet wireless fast charge off charge : Charging and water discharge in the pool are divided into three stages: pre-charging, constant current, and constant voltage (as shown below). You can also think of it as the process of putting water into a large pool. 2, of course, although millet wireless charging is equipped with a perfect automatic power off protection technology, but it is not recommended that you put it on the charging board for a long time, because your phone has been in standby state, this process will consume power to activate the working state of wireless charging, so the cycle of the battery or damage is relatively large, Serious accidents can also lead to safety accidents, so it is necessary to maintain good charging habits. 3, because millet's wireless charging treasure may charge frames and charging frequency and your Apple 8 p mobile phone charging frequency is not in the same frequency band. So in a few seconds it will automatically shut down and you can rematch your phone and then charge it. It is possible that the charging control circuit on the mobile phone motherboard is faulty. The distance between the charger and the mobile phone is too far. Millet milletThe line charger needs to fit with the phone to charge properly, and if the distance is too far, the light will keep flashing. The charger port is loose. The interface of the wireless charger must be correctly inserted into the power socket, and if the interface is loose, the light will always flash. There is a problem with the charger. Can be out of power, the protection status is blinking. When the millet wireless charger, millet wireless charger (universal fast charging version) LED light status is green flashing, millet wireless charger is in the error and protection stage. At this time, you should pay attention to whether there is a metal object placed on the wireless charger, please remove it and charge it again. It'll just take a second to cut the powerThis is not placed in the right position, metal foreign objects detected, automatic protection Settings. The charger itself has problems: the power cord of the charger is loose, the charging seat is damaged, the charging light is not up, etc., which will cause the charger to not work normally. Should check the charger itself has no problem, the problem is more serious, need to contact the after-sales service for repair or replacement. The green light of millet wireless charging will not flash three times, there are the following reasons: because the connection failure caused by the mobile phone protective shell is too thick. Wireless charger is not the official original charger, resulting in the mobile phone identification device is not successful. Wireless chargerPoor contact, resulting in the failure to perform normal wireless charging operations. The data line of the wireless charger is abnormal, resulting in the wireless charger cannot work normally. Indicator that it is charging: When the green light on the Xiaomi wireless charger starts flashing, it usually means that the charger is charging the device. This is a standard charging indication that the charger has been properly connected and is transmitting power. Possible problems or anomalies: However, a flashing green light may also indicate that some problem or anomaly has been encountered during charging. Xiaomi wireless car charging intermittently
Why does Xiaomi WPC01ZM wireless charger not charge for a while?