First of all, you need to shut down the iphonex phone completely Wireless charger disassembly tutorial , prepare the screwdriver Wireless charger disassembly tutorial , and remove the bottom two screws of the screen. Secondly, you need to remove the screen with a card, and remove the metal sheet screws of the old wireless charging module. Finally, remove the old wireless charging module and replace it with a new wireless charging module.
The top surface is provided with two round rubber pads, indicating two wireless charging areas, while charging and anti-slip protection equipment, killing two birds with one stone. There is a storage board on the right side, and the watch wireless charger can be fixed in the empty slot, and the Apple family bucket can be charged wirelessly through the charging board of the machine. When the storage board is in use, it can be taken out, and it can be pressed back when it is not in use, and it does not take up any space. There is also an LED charging indicator.
Using Apple's original charger to charge the mobile power through the Lightning port, the measured charging power is 5V 2A 10W. Move via USB-C portThe measured charging power is 8V 1A 18W. In turn, the USB-C port of the mobile power supply is used to charge the iPhone 12 Pro, and the charging power is 9V 2A 18W.
Method for wireless charging disassembly tutorial : Take the plug first because the IPHONE charger does not use screws, use glue, so only violent disassembly. The internal design of Apple's iPhone charger is very complex and high-end, which makes iPhone chargers more efficient and more secure. It's also an iPhone chargerOne of the reasons for the higher price of his mobile phone brand charger than its wireless charger removal tutorial . The iPhone charger can turn the input power on and off 70,000 times per second to output the correct voltage.
Apple charger is basically a buckle and glue, only violent disassembly, or take the sol a little bit of glue, but after 10 minutes, you will choose violence.
1. Turn off the device and disconnect the powerSource: Before performing any maintenance operations, be sure to turn off the device and unplug the power cord to avoid accidental contact with the current and resulting in injury. Remove the cover of the device: Carefully remove the cover of the device using a screwdriver and cover opener to replace the charging port. Unplug the old charging port: Pay attention to the connection mode of the old charging port, and follow the correct steps to unplug it.
2, screwdriver: used to remove the screw driver on the mobile phone: used to remove the rear shell of the mobile phone; : Replace the old tail plug before starting to work, remove the phone battery and mobile phone card memory card and other things, and then use a screwdriverRemove all screws from the shell. After all the screws have been removed, use the screwdriver to slowly pry the back shell up along the sides until the back shell is removed.
3, a good idea, I think in the barrel or somewhere to punch two holes, with two electrodes respectively connected to the positive and negative battery, charging the electrode connected to the charger is good, the change is very small, you can try.
How to use car wireless charging first of all to fix the car wireless charger toIn the appropriate position of the cab, connect the data cable connector of the wireless charger to the cigarette lighter interface of the car, and connect the other end to the wireless charger. After fixing the wireless charger, ensure that the wireless charger will not slip, and the wireless charger can be used normally.
The use of wireless charging of the car mobile phone bracket: Simply put, the wireless charging module and the mobile phone bracket are combined.
Before installing the support, ensure that the air conditioner outlet where the support is located is not warm, and check whether too many applications are running in the background of the phone. These high power consumption may affect the chargeThe electrical effect. If the temperature of the phone is higher than 35 ° C, the protection mechanism of charging current limiting or stopping charging may be activated, which will cause the efficiency of wireless charging to be reduced or unable to charge.
If your car does not have a USB port or you want to get the best adaptation and charging efficiency, you need to purchase a 12V cigarette lighter power base separately when choosing Green Link and Bex products. Because there is no electric clamp arm, the green link has lost a function point of the wireless charging mobile phone bracket compared to the ordinary mobile phone bracket, and it is not convenient to take the mobile phone, and the slightly more expensive Times and 360 function and appearance level are much better. Let's take a look at what we care about most