1, ready-made. Charging base Self-made wireless mobile phone charging , charging back sticker, charging head or charging treasure, charging line, assembled, can be wireless output wireless input, still can be wired charging Self-made wireless mobile phone charger ; Wireless charging waste of electricity is certain self-made wireless mobile phone charging , slow charging, low efficiency, heat, can not be separated from the base.
2, open the back cover of the smart phone self-made wireless mobile phone charger , and then take out the wireless charging receiver ready; Or the protective layer of double-sided tape peel; The next task is to connect the receiver's metal shock to the smartphone battery, which is the most difficult part of the process. But just be careful. PromiseEach metal electrocution can be connected together.
3, put the battery into the mobile phone; (Note: If the phone shell is metal it will not work properly homemade wireless phone charger !) Connect the transmitter board to the power supply, the green light flashes out, and enter the standby state; Put the mobile phone equipped with wireless rechargeable battery on the launch board, the universal mark on the launch board and the universal mark on the battery correspond to the red light, start charging; When the battery is fully charged, the red light turns back to green, the charging ends, and the system automatically shuts down.
4, Yes. Wireless charging is advantageousThe principle of electromagnetic induction to power mobile phones. In recent years, almost all mobile phone manufacturers are trying to apply wireless charging to mobile phones. However, after several years of attention, all products are still in the initial stage of adding coats to mobile phones. Samsung's technology is not mature enough to do wireless charging. So there are two contacts left in the rear cover of the Samsung I9300. Let's get everyone wireless charging. It failed.
5, the bottom also uses a magnetic charging coil, support 15w wireless fast charging, with wireless fast charging can get rid of the trouble of charging line. After you put the phone on, you can see the left and right side of the pressPlease ensure that the wireless charging bank has sufficient power Self-made wireless mobile phone charging , so as not to affect the charging effect.
2, but there are actually two problems here. If you use wireless charging in the form of a charging bank, you only need to put the mobile phone on the wireless charging bank, and then the power switch of the charging bank to open the power switch, he will directly carry out a wireless charging self-made wireless mobile phone charging .
3, first open the connection Settings on the phone, enable Bluetooth or NFC function. Charge the wirelessClose to the phone, touch the NFC area on the phone screen or select the wireless charger in the Bluetooth connection list to connect. After the connection, the wireless charging bank will automatically identify the type of mobile phone and adjust the output current according to different mobile phone models to provide the appropriate charging current for the mobile phone.
4, if your mobile phone directly with wireless charging function, just put the back on the side of the wireless charging bank can be charged. If your mobile phone does not have wireless charging function, you can plug in the mobile phone charging port through the attached ring charging sticker, and hide the module in the mobile phone case. And put it on a wireless charger. Be identified asAfter the phone will have "charging" prompt.
5, wireless charging bank charging Apple phone method is as follows: Apple phone has wireless charging function, just put the back of the phone on the wireless charging bank can be wireless charging area to start charging. The iPhone does not have a built-in wireless charging function, so it needs to be achieved through the attached ring charging sticker. First, find the insertion port on the ring patch and plug it into the flash port of the phone.
Connect the MicroUSB or Lightning port on the module to the phone. If there is double-sided tape on the receiver, you can glue it directly to the back of the phone. If it doesn't come with it, you have to figure it out yourself. Choose the most suitable position, be careful not to let the part of the connection line have the phenomenon of warping. Then you can put the phone on the wireless charging dock to experience the wireless charging function.
First of all, we need to have a clear answer to the problem: the electromagnetic cooker is widely spread on the Internet to charge the mobile phone, indeed, someone really did it successfully!! howeverThe process is not by placing the mobile phone that supports wireless charging directly on the induction stove, but by making a self-made coil to generate electromagnetic induction, and after a series of depressurizing, the voltage is reduced to 2V DC voltage and then the mobile phone is charged.
ready-made. Charging base, charging back sticker, charging head or charging treasure, charging line, assembled, can be wireless output wireless input, still can be wired charging; Wireless charging waste electricity is certain, slow charging, low efficiency, heat, can not be separated from the base.
Yes, the problem is that the phone itself needs to support, or transform the phone, the so-called wireless chargingElectrical appliances, originally is a wired charger, plus a transmitter coil, and then the mobile phone has a receiving coil, so that it can be charged, to be honest, don't be superstitious, there are many problems, put on the position is very important, sometimes because of the ready to put, the position is not allowed, resulting in slow charging, or even no charging at all, will delay the matter.