Puppy t10 vacuum cleaner charging instructions: You can plug in the charger for a while and see if you can charge it. Generally adhere to about an hour is appropriate, if not charged, it needs to check whether there is a circuit protection device, if there is that can be unlocked, there is no circuitIn the case of protective devices, that may be battery damage.
indicates charging. When the dog is charging, the four lights flash together to represent that it is charging, and it does not flash when it is full.
The puppy vacuum cleaner can not be charged because the power plug is not firmly inserted in the power socket, you need to pull the plug off, and then reinsert the power socket. The dog vacuum cleaner can not be charged may be no power outlet, you need to open the circuit breaker check, if there is a problem, you need to ask a professional electrician to repair.
The first layer of the foam frame is a vacuum cleaner metal extension tube and a second combinationThe brand mission of vacuum cleaners, 23 years has always focused on the development and innovation in the field of vacuum cleaners.
2, does the question want to ask "dog mite control instrument charging when the light has been flashing"? The battery is faulty. When charging the dog mite detector, the light has been flashing because the battery is used for a long time or aging, which belongs to the battery reason, the solution is to replace the new battery, and make sure to use the appropriate charger.
3, you want to ask the dog vacuum cleaner when charging the red light is the reason? The reasons why the puppy vacuum cleaner flashes red when charging are as follows: The power socket and battery socket are not plugged in properly. Charging plug and power plugThe seat is not inserted properly. The battery is low. The motor has difficulty rotating. Dust cup detection is not in place. The battery of the infrared remote is dead. The value of Puppy vacuum cleaner is that everything is user-centric, providing vacuum cleaners for families around the world.
4, battery aging may be the battery of the vacuum cleaner aging, so that the battery will not be charged, the red light showing the power, if this is really the case, it is best to send the vacuum cleaner to the repair shop to repair it, or directly replace a new battery. The red light here is not a power indicator, but a dust indicator, and the dust cup of the vacuum cleaner is filled with garbage, if it is too dirtyThe red light will stay on.
5, when the portable vacuum cleaner is charged, the three lights are not charged at the same time. It is common that the battery is not automatically protected for a long time, the battery is not charged, or it is not charged, the output insurance has been burned, the charger's own quality problems, the battery is placed for too long, or the battery plate has a short circuit, resulting in too low voltage. In this case, take the vacuum cleaner to a repair shop for an overhaul and let a professional repair it.
6, for the reason that the dog vacuum cleaner is red, there are the following possibilities: The trash can is full: The red light indicates that the trash can has beenFull, please empty the trash can and continue to use. Filter blockage: The red light may indicate that the filter is blocked, please clean or replace the filter. Power problem: The red light may also be because the charger is improperly connected or the power cable is faulty. Please confirm whether the power connection is normal.
Power failure is one of the common problems that cause the vacuum cleaner to fail to charge. First, check whether the socket is working properly, try to connect other appliances to the same socket, and confirm that the power supply is normal. If there is no problem with the socket, check the vacuum cleaner power cord for damage or poor contact. Sometimes, the power cord may be worn or broken due to prolonged use, resulting in abnormal charging. At this point, you need to replace the power cable and try charging again.
Maybe the battery is broken, so it can't be flushed into the power. So this is the time to replace the original battery. Because batteries have a life spanUsually 2-5 years. Specific with the use of the environment has a direct relationship. There are various causes of failure, and it is necessary to check, test and judge gradually from outside to inside, from mechanical to electrical, from software to hardware.
Battery bad, battery bad, charging does not enter, charging current is small, natural green light.
1, from the measurement of the charger output end (low voltage, connected to the vacuum cleaner battery) plug the corresponding voltage, if there is 12V/16V/24V electricityThe charger is fine when pressed. The absence of this voltage means that the charger is faulty and needs to be repaired. The charger is not difficult to repair and the parts are not expensive to update.
2, the filter is blocked: the red light may indicate that the filter is blocked, please clean or replace the filter. Power problem: The red light may also be because the charger is improperly connected or the power cable is faulty. Please confirm whether the power connection is normal. Fault status: The red light may also be because the vacuum cleaner is faulty, please contact the after-sales service or check maintenance.
3, the voltage method is one of the most used methods to check and judge the charger fault, it is mainly through the measurement of the charger circuitThe end point voltage and the working voltage of the components, and the comparison and analysis with the normal value, can draw the conclusion of fault judgment. The higher the internal resistance of the multimeter used for measurement, the more accurate the measured data will be.
4, you have to look at the charging connector is not dirty things caused by poor contact, each plug is not strong, if not for these reasons as soon as possible to contact customer service, they must have more professional guidance and solutions.
5, indicator light method, voltage method, etc. Indicator method: After entering the mains voltage for the charger, if the power indicator is not on, it indicates that the charger is not working. Voltage method: Use a multimeterMeasure the voltage of the main end points of the charger circuit and the working voltage of the components, and compare and analyze with the normal value. If it is abnormal, the charger is abnormal.
6, the dog vacuum cleaner can not be charged because the power plug is not firmly inserted in the power socket, you need to pull the plug off, and then reinsert the power socket. The dog vacuum cleaner can not be charged may be no power outlet, you need to open the circuit breaker check, if there is a problem, you need to ask a professional electrician to repair.
1, the charging port is located at the bottom or side of the vacuum cleaner, insert the charger plug into the charging port of the vacuum cleaner. Plug the other end of the charger into a power outlet, and once the charger is connected to the power supply, the vacuum cleaner will start charging.
2, you can plug in the charger for a while and see if you can charge it. Generally insist on about an hour is appropriate. If you do not charge, you need to check whether there is a circuit protection device, if there is that can be unplugged. If there is no circuit protection device, it may be the battery is damaged, then you can replace a new battery, and then it should be OKSolved the problem.
3, red, blue, green. red. When the dog mite control machine is insufficient, it will show a red situation. blue. The blue light flashing on the charging of the puppy mite control instrument means that the puppy mite control instrument has been fully charged. green. Puppy mite control meter charging green flashing indicates that it is charging.
4, the dog sweeping robot r60pro how to correctly charge 6400mAh large-capacity lithium battery than the previous generation power increase by 2 times to ensure that the suction is large enough, a single battery life of up to 4 hours, built-in 450ml large-capacity dust box, no need to pour dust halfway, easy to driveCleaning tasks for large apartment types. Automatic recharging at the end of each cleaning, support breakpoint continued scanning function, fully charged back to the original position to continue to work, a sweep is not completed next time.
5, you have to look at the charging connector is not dirty things caused by poor contact, each plug is not strong, if not for these reasons as soon as possible to contact customer service, they must have more professional guidance and solutions.