The current wireless charging Alliance (WPC) formulated the Qi standard of the charging frequency is generally about 100kHz, it is recommended to look at this standard, it is the current more mainstream standard in wireless charging.
Wireless charging, using the principle of electromagnetic induction, the working frequency is very low, and the risk is small. If you're still worried, you can choose and defend your plan.
w. At present, domestic mobile phones already support 50W wireless charging, 50W is also the upper limit of the interim standard for wireless charging, but even so wireless chargingThe frequency of use of electrical appliances is still not as good as the traditional charger, and Samsung launched a 15W wireless charger at this time, which is really confusing.
To effectively reduce the adverse effects of electromagnetic radiation on health. For mobile phones: under normal circumstances, it will not harm the mobile phone, and the working frequency of wireless charging is now below 1M, so it will not affect the signal of the mobile phone. Wireless charging has no effect on mobile phone battery life, and wired charging is basically the same, but the rate is lower, but the wireless charger conversion rate is still high, more energy saving.
2, Haval h6 wireless charging power 40 watts. Make sure that the door is closed and the key is in the car, switch the ignition switch to ON mode or start the vehicle, press the charging button, turn on the wireless charging function of the mobile phone, and place the mobile phone in the charging area to start charging. In order to achieve a better charging effect, make sure that the charging coil of the mobile phone is facing down.
3, in the three major items that users are concerned about, the third-generation Haval H6 also carries out Wireless charging 127.6KHz New upgrade. In terms of power, the third-generation Haval H6 is equipped with 5GDIT EVO engine, the maximum power is 124kW, the maximum torque is 285Nm, thanks to the new turbocharger, the maximum torque output range of the third-generation Haval H6 is increased from 14003000 RPM to 14003600 RPM, the acceleration performance is better at low speed, and the acceleration is more powerful. 4, interior, the third generation of Haval H6 uses a minimalist design language, but its interior materials and layout are more advanced. Suspended by 13 inchesThe center console combined with the touch screen and 25-inch full LCD instrument creates a strong scientific and technological atmosphere for the new car. In addition, the new car is also equipped with HUD display, wireless charging of mobile phones, leather seats and other configuration, so that the comfort and entertainment in the car have been greatly improved.
5, of course, the air purification system, mobile phone wireless charging, intelligent AI interaction and other new features will not be absent. The third-generation H6 uses a panoramic electric skylight with a lighting area of 0.82 square meters and an opening area of 0.35Square meters, more spacious than many of the same class. The seats are soft and the front seats have power adjustment. The rear is also more spacious due to the increased wheelbase.
6, the third generation of Haval h6 is indeed equipped with wireless charging function, which brings great convenience to the driver. The realization of wireless charging function is based on the principle of electromagnetic induction that we learned in middle school. When the magnetic field changes, a current is generated in the conductor, thus achieving wireless transmission of electrical energy. Although the principle is not complex, wireless charging technology has not been widely used in the past, mainly because of the lack of industryThere is no uniform standard.
The basic principle of wireless charging is to convert the current into a magnetic field, which is transmitted through the air and then converted into a current to be transmitted to the intelligent terminal. When the system works, the input end converts the AC mains into direct current through the full bridge rectifier circuit, or uses the 24V direct current end to supply power to the system directly. After passing through the power management module, the output direct current is converted into high-frequency alternating current through the 2M active crystal oscillator inverter to supply the primary winding.
Wireless charging system mainly adopts the principle of electromagnetic induction. Wireless charger refers to the charger that does not need to be connected to the terminal device that needs to be charged without the traditional charging power cord, using the latest wireless charging technology, through the use of the magnetic field generated between the coils, the magic transmission of electrical energy, inductive coupling technology will become a bridge connecting the charging base station and equipment.
Generally seen wireless charging, the use of the "current magnetic effect" and "electromagnetic induction" principle. In 1819, Danish scientist Elster observed that if there is an electric current on a wire, a magnetic field will be generated around it, which can deflect the north finger. Later, it was further discovered that the wire was encircled in a ring, and evenWound into a coil, the resulting magnetic field will be stronger and more concentrated, which is called the "current magnetic effect".
No strong radiation, no effect on the human body! The main principle is: the way of wireless charging is electromagnetic induction, magnetic resonance, electric field coupling and radio wave transmission, etc. Most of the wireless charging of mobile phones uses the principle of electromagnetic induction.
Wireless charging, also known as inductive charging or non-contact inductive charging, based on the principle of electromagnetic induction, it is not necessary to transmit electricity to the device like the traditional wired charger, but the device that needs to be charged can be charged by contacting the wireless charging base