1, coil using enamelled wire Wireless charging wire , 180 polyurethane imide (QZY/EIW) used in some common small power transformers Wireless charging wire , such as power transformers on some home appliances, mobile phone chargers, etc., enameled wire has good comprehensive performance. The thickness and the number of turns have to be actually calculated wireless charging line , the thickness should be able to bear the current through, the number of turns depends on the transformer coefficient, the conversion of energy.
2, winding transformer usually used materials are enameled wire, sandbagWire, silk-covered wire, the most commonly used enamelled wire. The requirements for the wire are good conductive performance, sufficient heat resistance of the insulating paint layer, and certain corrosion resistance. Like the wireless charging special wire We use this Novo electrical equipment, the win-win transformer, all use high-strength polyester enamelled wire.
3, enameled wire is an insulated wire coated with paint, so it can be wound into a variety of shapes of coils used in a variety of electronic devices, without producing the phenomenon of short circuit between wires. ● If it is not enamelled wire, use other insulationMaterial wrapped wires, such as gauze-covered wires, silk-covered wires, insulated pipe lines, etc., can also be used as coils.
4, silk-covered wire Wireless filling special wire : a copper wire wound glass fiber wire as insulation skin. Enamelled wire: a copper wire is attached to a chemical insulating material as an insulating skin. The breakdown voltage of silk-covered wire is only a few hundred volts, the breakdown voltage of enameled wire is several thousand volts, if the insulation is no problem, I think it is possible to exchange.
Connect the standard charger and data cable of the mobile phone to the wireless charger, and then put the mobile phone directly (vertically) or horizontally in the center position of the wireless charger base, you can realize wireless charging, the indicator light will have a breathing effect, 5 seconds later, plug and play, convenient and quick.
Connect the charger (the charging head that comes with the phone or is purchased separately) to the power source. Connect the data cable Connect the charger to the wireless charger using the data cable. Place the phone Place the rechargeable area of the phone in the center of the upper surface of the wireless charger, and the phone shows that it is charging. The specifications of the charger used with the wireless charger will be changedThe actual wireless charging power is affected. It is recommended to use the standard charger of the mobile phone, and the maximum wireless charging power supported by the mobile phone is not exceeded.
Mobile phones use wireless charging, you need to buy a wireless charging base or wireless charging back case to use. Connect the charger to the wireless charging base, and then place the phone or a phone with a wireless charging back case on the wireless charging base. Take off the holster If the phone's holster is too thick or not the original charging holster, it may affect the charging effect, it is recommended to take off the holster and try charging.
If your Huawei mobile phone supports wireless charging, wirelessAfter the charger is powered, the phone can be charged directly by placing the screen facing up in the center of the charger or in the position suggested by the manufacturer.
Start the wireless charger in the car: usually find the accelerator of the car first, and then use the car key to ignition the car, and then the wireless charger will automatically open. Put the helmet on the phone: Place the phone on the wireless charger in the car, and then put the helmet on the phone, taking care to ensure that there is a dense contact between the helmet and the phone.
Connect the charging head to the charging base using a data cable, and then plug the charging head into the power supply. Place the charging base on the desktop and place the phoneLine charger is not to buy another data line, because the box to buy wireless charger should be attached with a data line, used to connect the wireless charger, the data line this thing is relatively low cost, the price is relatively cheap, not to give you, but also you to buy, this is very bad for the consumer experience, he does not need to do so.
3. After the wireless charger is powered, place the phone screen facing up directly in the center of the charger or the position suggested by the manufacturer to charge.
4, Huawei mobile phone wireless charger usage steps: Connect the 9V2A charger to the socket and connect the numberAccording to the line. Cable usb-c side connects to wireless charger. Place the charging area of the phone with wireless charging function in the center of the surface of the wireless charger. You can see that the phone has shown that it is charging. For information on charging areas, refer to the phone's instructions.
1, car wireless charging is suitable for most mobile phones with wireless charging configuration on the market; For example, Huawei Mate RS, Mate20 Pro/RS, P30/P30 Pro, Mi 9/Mix2S/3, most of Samsung's series, mobile phones without this configuration can also achieve wireless charging through wireless charging patches. Recently, Xiaomi launched a smart car charger, Xiaomi wireless car charger Pro, which has been officially launched, which is a small edition of me, but a necessity of life.
2, wireless car charger can only clamp a certain width of the mobile phone, and the clamping instability may be that the width of the mobile phone is too small, can be replaced with a wireless car charger of other specifications, you can also try to carry a mobile phone cover to the mobile phone to improve the width of the mobile phone. The clamping force of the iron clamp of the wireless car charger is insufficient, which causes the clamp to be unstable and can be replacedA fitting car charger clip. 3, this car charger is compatible with a variety of wireless charging devices, not only can provide 10W fast charging for Xiaomi Mi 10 Pro, but also can provide fast charging for Samsung S20 series and new iPhone 11 series. Its effective charging induction of 4mm, even with a mobile phone case can be charged normally. The wireless car charger universal fast charging version is similar to the ordinary mobile phone holder in appearance, with a wireless charging board as the main body and a clamp arm design on both sides.
4, millet wireless car charger is a device that can be charged wirelessly in the car, it uses the latest Qi NoLine charging technology supports fast charging and works with most mobile phones, including iPhone and Android phones. Xiaomi wireless car charger has the characteristics of easy to use, fast charging, safety and so on. It uses dual-mode compatibility and supports three charging modes of 5W/5W/10W, which can meet the charging needs of different mobile phones.
5, millet wireless car charger compatibility is still relatively wide, can be compatible with a variety of wireless charging equipment. It can charge not only a variety of Xiaomi phones, but also multiple brands of Samsung phones and Apple phones. It should be noted that only the hands that support wireless charging technologyThe machine can use wireless car charging, so you can check whether your mobile phone model supports wireless charging technology.