This condition is usually caused by the fault of the phone charger. If the actual output voltage of the mobile phone charger is lower than the rated output voltage, then during the charging process, when the battery voltage of the mobile phone rises to a certain value, but does not fully charge the battery, the current voltage of the mobile phone battery is consistent with the output voltage of the charger, so there is no voltage difference that will cause the charging to stop. It is recommended to replace the charger for testing.
Check whether the original charger is used. If not, please replace the original charger and try again. Try replacing another power socket. If the battery can be removed, reinstall the battery or replace it with another original battery and charge it again. Update the mobile system version: Settings - About the phone (about the device) - manual download updates/automatic download updates (software update/System update - Update). Note: Back up the data on the device before the upgrade.
If you confirm that the model is OK, but there is still no wireless charging, you can refer to the following methods to try to solve it. Reboot your iPhoneIf the iPhone wireless charging suddenly does not charge, it may be because there are sometimes unpredictable errors in the update of the iOS system, which will cause problems with the wireless charging function, usually as long as the restart can be solved.
Wireless charging is not mature, it is like the previous black and white TV, the signal is not good, take two normal. But wireless charging can not see the radio wave, this can only be taken to the expert to see.
Hello, if you use a wireless charger, there is always an intermittent charging prompt tone, it should be that the back of your phone is not accurately placed on the wireless charging contact surface, andIt may be that your phone case affects wireless charging, you can remove the phone case and try again.
There is a problem with the charger or charging cable Wireless charging can not be charged for half a day There is a problem with the mobile phone battery. There is a problem with the charger or charging cable: Make sure you are using an Apple certified charger and charging cable Wireless charging will not charge for half a day , and check for damage or wear.Mobile phone battery problems: mobile phone battery has been aging or damaged Wireless charging for half a day can not be charged , will also lead to wireless charging can not work properly, need to replace the battery.
And wireless charging needs to be achieved through electromagnetic induction, and aluminum alloy does not have this function, so Apple XR can not support wireless charging. Cost considerations Another reason is cost considerations. Wireless charging requires the addition of additional hardware components, which increases production costs. The Apple XR is positioned as a mid-range model, and in order to control costs, Apple may make some compromises on hardwareWireless charging is one of them.
If the warning "Accessory is not supported" or "accessory is not certified," it may be that the charging accessory is faulty, damaged, or not certified by Apple, or it may be that the charging port of the iOS device may be dirty or damaged. Please check the charging accessories for problems or replace them, and carefully clean the charging interface.
Apple mobile phone display charging but not charged into the general reasons and treatment methods: for non-original charger, this situation will often occur, which is caused by the charger specifications are not up to standardReplace with a qualified charger. If the original charger has the above fault, please continue to look down. Please check whether the data cable is normal. The data cable looks normal on the outside, but it may have been broken inside.
The causes are as follows: In the notification bar, click the button to enable wireless reverse charging. The charged device needs to be placed in the correct position in the center of the rear cover. The device to be charged needs to support the standard Qi wireless charging protocol (for example, AppleWatch is a non-Qi wireless charging device, which cannot be charged through the wireless backcharging function). There can be no metal trim or gold between the phone and the device being chargedng> Wireless charging can not be charged for half a day Wired charging equipment if wired charging and wireless charging are used at the same time, wired charging will be preferred.
2, Make sure that the phone and wireless charger compatible: to make sure that your phone supports wireless charging function, and the wireless charger is compatible with your phone model. Different phone models may have different charging standards, so you must use a wireless charger that supports your phone model. Check the charger and power adapter: make sure the wireless charger is working properly and connected Wireless charging can not be charged for half a day The appropriate power adapter, make sure that the power adapter plug is firmly inserted into the power outlet.
3. Please check whether the wireless reverse charging switch is turned on. The phone setting path is as follows: Set the battery and turn on the wireless reverse charging switch. Please confirm whether the battery of your charging phone is above 20%.
4, the mobile phone protection case is too thick: when the mobile phone protection case is too thick, it will affect the wireless charging of the mobile phone. Thus Wireless charging can not be charged for half a day We can take off the mobile phone protective shell and then charge it. Motherboard failure: After the above operation, if the fault is still, then wireless charging for half a day can not be charged We can best take the mobile phone to the mobile phone repair shop for warranty processing or maintenance, must not be in the case of no experience, randomly disassembly machine, to avoid unnecessary losses.