First, prepare the wireless charging kit, including the battery compartment cover and the required tools. Weld cell cover contacts to test kit. Then, connect the welded wire to the phone charging pin to confirm the connection is correct. Then, carefully remove the induction coil, install it on the phone, weld the charging pin, and finally test whether the wireless charging function is displayed normally.
willThe standard charger and data cable of the mobile phone are connected to the wireless charger, and then the mobile phone is placed in the center position of the left and right of the wireless charger base, wireless charging can be realized. The indicator light will have a breathing effect, and it will be extinguished after 5 seconds.
After the wireless charger is powered, directly place the phone screen facing up in the center of the charger or the position suggested by the manufacturer to charge. If your Huawei mobile phone supports wireless charging, you can directly charge the wireless charger by placing the mobile phone screen facing up in the center of the charger or the location recommended by the manufacturer. First, click on the desktop of the phone to open the 【
1. The steps for connecting the wireless charging bank to the mobile phone are as follows: Ensure device compatibility: Check whether the mobile phone supports wireless charging. Mobile phones that support wireless charging can only be connected to wireless power banks. Charging bank pre-charge: Plug the wireless charging bank into the power supply or USB port of the computer to charge. During the charging process, ensure that the wireless charging bank has sufficient power to avoid affecting the charging effect.
2, but there are actually two problems here. If you are using wireless charging in the form of a power bank, you only need to put the phone on the wireless charging bank, and then the power switch of the charging bankTurn on the power switch, and he'll go straight to a wireless charge.
3, first open the connection Settings on the phone, enable Bluetooth or NFC function. Touch the NFC area on the phone screen or select the wireless charger from the Bluetooth connection list to connect. After the connection, the wireless charging bank will automatically identify the type of mobile phone and adjust the output current according to different mobile phone models to provide the appropriate charging current for the mobile phone.
4, if your mobile phone directly with wireless charging function, just put the back on the side of the wireless charging bank can be charged. If your mobile phone does not have wireless charging function, you can plug in the mobile phone charging port through the attached ring charging sticker, and hide the module in the mobile phone case. And put it on a wireless charger. After the recognition is successful, the phone will have a "charging" reminder.
5, if the Apple phone already has the wireless charging function, just put the back of the phone on the wireless charging bank can be wireless charging area to start charging. If the iPhone does not have a built-in wireless charging function, it needs to be achieved through the included ring charging tape. First, find the insertion port on the ring patch and plug it into the flash port of the phone.Then, the ring patch is hidden in the phone case.
6, prepare the accessories needed for charging, Qi wireless charger, wireless charging receiving coil. With these ready to go, we're ready to operate. Plug the wireless charging receiver coil into the phone port, just like you normally charge. Plug in the receiving coil. After the link is good, the wireless charging receiving coil is finally placed on the back of the phone, without affecting the use of the case.
1, the method of making wireless charger is as follows: Attach the module to the MicroUSB port comparison place. Connect the MicroUSB or Lightning port on the module to your phone. If there is double-sided tape on the receiver, you can glue it directly to the back of the phone. If it doesn't come with it, you have to figure it out yourself. Choose the most suitable position, be careful not to let the part of the connection line have the phenomenon of warping.
2, soldering iron, copper wire, resistor, transistor, capacitor. That will do. So wireless charging is simple. But I suggest you don't do it yourself. It's all special materials. If you do it for fun, just make an oscillating circuit.
3, one of the self-wound coil connected in the charging circuit, 555 output foot (third foot) with an output tube (at your own will, but to the high-frequency power tube) output tube link self-wound coil, will be connected to the two coils close (about 1 cm or so there is a very sufficient charging current) power can be wireless charged! The efficiency of this circuit is very low, because there is only half a wave peak high frequency so the loss is relatively large, but the principle is quite simple and easy to produce.
1, can buy a wirelessThe charging receiver is affixed to the back of the mobile phone or inserted into the charging port of the mobile phone. The advantage of this method is that the cost is low and there is no need to replace the mobile phone or disassemble the inside of the mobile phone. The disadvantage is that it may affect the beauty and feel of the mobile phone, as well as increase the wear and tear of the charging port.
2, first of all, cut the USB charging cable into two sections not far from the two ports. Use scissors to separate the tail glue of the two wires into a section to screen and then cut off the green wire with a double bottom line. Use hot glue to attach the magnet to the charger. Wrap the wires in the USB with tinfoil. Then wrap the wires and roll them up with copper wire. The US of the copper wire will be rolledThen wrap them in electrical tape on line B.
3, to add the wireless charging function to the ordinary mobile phone, the most critical is to install a wireless charging receiver. This process usually involves opening the case of the phone, finding where the battery or battery is connected, and welding or connecting the receiver to the appropriate circuit. This requires a certain amount of electronic knowledge and fine manual skills, because the components inside the phone are very small and fragile.
Simple that on your pictureIf there are no other accessories, basically, unreliable, don't try. The principle of wireless charging is very simple, using the most basic principle of electromagnetic conversion, that is, the changing magnetic field generates an electric field.
If there is double-sided tape on the receiver, you can glue it directly to the back of the phone. If it doesn't come with it, you have to figure it out yourself. Choose the most suitable position, be careful not to let the part of the connection line have the phenomenon of warping. Then you can put the phone on the wireless charging dock to experience the wireless charging function. The next task is to electrocute the receiver's metal with the smart handThe battery is connected, which is the most difficult part of the whole process.
Yes, the problem is that the phone itself needs to support, or transform the phone, the so-called wireless charger, is originally a wired charger, plus a transmitter coil, and then the phone has a receiving coil, so that it can be charged, to tell the truth, don't be superstitious, there are many problems, put on the position is very important, sometimes because of the ready to put, the position is not allowed, Resulting in slow charging, or even no charging at all, will delay things.
There are many ways to make radio chargers on the Internet, but we will find out after hands-on operationThose are too complex, either the circuit is too complex, or important components can not be found, or their own environment is not enough.
Then only need to change a battery can be wireless charging. But this model will be out of the prototype in September this year, installed in the battery is the best popular method.