1, the use of car phone suction cup is to suck it on the front windshield: mobile phone suction cup as a simple mobile phone stand, watching video is more convenient; Mobile phone suction cup is a vacuum suction cup, also known as a vacuum sling, is one of the executive mechanisms of vacuum equipment; The sucker material is made of nitrile butadiene rubber, which has a large tearing force, so it is widely used in various vacuum sucker equipment.
2, the installation and use method of the car phone bracket suction cup is to fix the phone suction cup on the front windshield. In this way, you can easily watch mobile phone videos and improve the safety of driving. Mobile phone suction cup is a vacuum suction cup, also known as a vacuum sling, is one of the actuators of vacuum equipment. This suction cup is made of nitrile butadiene rubber, which has a large tearing force, so it is widely usedIn a variety of vacuum sucker equipment.
3, the use of car suction cup mobile phone holder can be very convenient to fix the mobile phone in the car, improve driving safety and navigation convenience. The installation process is also very simple, as long as the suction cup of the support is adsorbed in the lower middle of the front windshield, and the fixing clip is adjusted, without the use of any tools.
4, the use of car phone suction cup is quite simple, just adsorption on the front windshield can be. As a convenient phone holder, it makes it easier to watch videos in the car. This kind of mobile phone sucker uses the vacuum adsorption principle and has strongYou can just pull the glue off. If it is screwed on, use a screwdriver to unscrew it. Welded on can only see or find a 4S shop to help replace an air outlet.
2, first of all, you need to understand that there is a layer of glue stuck in the middle of the suction cup. Use the blade or knife to rotate slowly, taking care that the knife is flat or face up to avoid scratching the phone. The suction cup can be easily removed by rotating it once. Use a hair dryer or air conditioner and toothpaste. If your phone is sticky, you can turn it off and use a hair dryer or air conditioner and toothpaste. A hair dryer softens the glue, while a cream and toothpaste remove it.
3, car phone stand suction cup removal method: if the use is sticky (similar to the hook) the glue, directly pull it off. If it is screwed on, use a screwdriver to unscrew it. If welded on it, you can only use a saw or find the 4S shop to help replace an air outlet, and then remove the air outlet, and then remove the support; The round iron sheet is the car mobile phone bracket, which is the most comfortable, simple and easy to use digital bracket.
4, remove the steps of the car phone bracket: First of all, for the use of adhesive fixed bracket, just gently pull to remove; For tightening installation,Loosen gently with a screwdriver. If you encounter difficulties, such as the inability to remove the air outlet support, you may need to seek technical support from a professional 4S shop. Some of the brackets are cleverly designed to support replacement fixing to accommodate a variety of devices such as tablets, mobile phones, MP4 or PDAs.
5, do not hard dial, because the suction cup and the base is vacuum connection, hard dial is the wrong way to take the support, you can turn the support by hand, let the air slowly into the suction cup, you can easily remove the support.
Are you using a magnet holder or a double suction holder? It is recommended that you use the air outlet bracket, or dolphin bracket, or sucker bracket, these will not appear to suck unstable situation, it is recommended that you Baidu to look at the car record bracket.
Apply water or soapy water: Before attaching the suction cup, you can apply one to the inside of itSome water or soapy water. This can increase the viscosity of the sucker and improve its adsorption force. Heating treatment: If the above methods are not effective, you can try to use hot water or a hair dryer to heat the suction cup. After heating, the suction cup will become softer and easier to adhere to the surface. However, please be careful not to overheat, so as not to damage the sucker.
Rinse with water, gently rub with soap bubbles, shake dry; Wipe the attached glass surface, the chassis is a little wet, and then suck it up (the bottom is supported on the center console); Choose thick spongy double-sided tape; Put some water on the suction cup, or rub egg white on it to increase itSuction. With the improvement of people's material life, playing tablet computers, mobile phones, etc., has become a fashionable way of life.
Believe that many owners who install navigation brackets for the car will have a problem, that is, the suction cup of the navigation bracket cannot stick to the console, so what method can make the suction cup stick more firmly? Let's take a look.
The working principle of the suction cup is to exhaust the air by extrusion, forming the internal and external pressure difference, and using atmospheric pressure to firmly adsorb the suction cup on the glass surface. Over time, the suction cup may fall off because the surface of the suction cup is not completely flatThe whole, resulting in air into the inside of the sucker, when the internal and external pressure is equal, the sucker will lose the adsorption force.
1, [Pacific auto network] The occurrence of suction cup type mobile phone frame can not absorb suction cup wireless fast charging car situation: rinse Suction cup wireless fast charging car with water, dip some soap bubbles gently rub Suction cup wireless fast charging car , shake dry Suction cup wireless fast charging car ; Wipe the attached glass surface, the chassis is a little wet, and then suck it up (the bottom is supported on the center console); Choose thick spongy double-sided tape; Add water to the suction cup, or rub egg white on it to increase suction.
2. Use soapy water. For better results, use soapy water. Apply soapy water to the suction cup and quickly glue it on. When it dries, you can hang your stuff. It worked very well. The handling method of the suction cup of the mobile phone holder is as follows: 1.
3, if the car support suction cup can not suckThe situation is to first take off the support, and then wipe the glass surface to stick, and then add a little water to the chassis to get wet or add a little egg white, and then adsorb it will be better, because these two things will enhance its adsorption force. Another way is to use strong double-sided tape to stick it to the glass. 4, if you have tried all the above methods, but still can not solve the problem, then there may be a problem with the suction cup itself. It is recommended to replace the sucker with a new one. Question 3: How to do if the suction cup fails to absorb this problem usually involves twoFirst, the problem of the substance itself. For example, the walls are not clean, there is dirt on the suction cups, and the walls have gaps. The solution is to thoroughly clean up the dirt and voids. Second, the working principle of the suction cup is blocked.
5, make the suction of the navigation bracket more firm method If the navigation bracket cannot suck, you can take the bracket off, and then wipe the bottom of the navigation bracket and the position of the bracket together, and then add some water to wet the suction cup, or replace the water with egg white liquid, these two things can effectively increase the adsorption force of the suction cup. Then just attach the navigation bracket back on.