中文English
如何拆无线充ichaiyang 2024-06-01 15:16 78
1, How to remove the wireless charging board of Lynk & Co 05 2, How to dismantle Regal wireless charging drawer 3, How to remove Apple wireless charger without damage? 4, How t...

How to remove wireless charging (How to remove wireless charging pump)

How to remove the wireless charging board of Lynk & Co 05

The wireless charging board configured for Lynk & Co 02 is set in the storage grid below the center control, and it only needs to be equipped with the wireless charging function when the vehicle is powered onWireless charging can be realized on the panel, and wireless charging is currently low charging efficiency, which can be used as an emergency need.

This "Dismantling Lab" program is the first dismantling explanation of Lynk & Co 05 PHEV on the whole network. By the professional answer of Zhihu formed a "dismantling day group" to the vehicle parts level disassembly - vehicle performance integration engineer Wang Xiaopeng PPGarafe, car answer master Kang mean cat, new energy technology chief engineer Kebab, green core channel three power engineer small Feigu, quality engineer picket daydream car and car technology column main writer Kai Kai, has attracted widespread attention in the industry.

inWhen using wireless charging, make sure there are no other objects on the WPC panel, just the phone. You also need to turn on the intelligent interconnection NFC and wireless mobile phone charging function inside the central control setting, and then confirm the wireless charging function through the mobile phone operation, and finally put the mobile phone in the center of the charging board to start charging. It should be noted that at the current level of technology, wireless charging efficiency is not high, and there is a serious problem of heat generation.

Need to make sure that there are no objects on the surface of the WPC. 2 Click Functions -- Settings -- Smart Connect -- NFC and wireless phone charging on the central display. 3 TapsMobile phone wireless charging, activate/deactivate the function. 4 Place the phone in the center of the charging pad. After the charging of Lynk & Co 02 wireless mobile phone starts, it will be displayed at the bottom right of the screen, and stop charging when the phone is full. Keep metal objects away from the charging pad when charging, as metal objects may overheat the pad.

The opening method of Lynk & Co wireless charging is: click the function button on the central display; Swipe down the page to find Settings and click; Click Smart Internet to turn on nfc and wireless charging. Taking the 2020 Lynk & Co model as an example, it is a compact suv with a body length of 45,92mm and a height of 1879mm, 1628mm, the tank volume is 52l.

How to dismantle Regal wireless charging drawer

1. Pull the push-pull drawer that needs to be removed until it cannot be pulled. At this time, we are at the left and right sides of the drawer slide rail, the left side can see a downward sloping plastic buckle. On the right side of the drawer, there is an upward sloping button, the color is usually black or white. Then, use your hand to press the left button up, the right button down, and vice versa, you can feel the drawer slide.

2, if you want to remove the drawer, first pull the drawer outward to the maximum extent, so that you can see the long black plastic tip buckle on the side of the slide rail, and then the buckle on both sides of the drawer slide rail at the same time up, down or up and down, hold down and pull the drawer back, you can open the guide rail to remove the drawer. Use a screwdriver to remove the two sliding rails fixed inside the cabinet.

3, we pull the drawer as far as possible, then there is a long black tapered buckle. With the hand to the black protruding long buckle, press down (most cases are down, do not exclude to lift up), longRemove the bottom two screws of the curtain. Secondly, you need to remove the screen with a card and remove the metal sheet screws of the old wireless charging module. Finally, remove the old wireless charging module and replace it with a new wireless charging module.

The top surface is provided with two round rubber pads, indicating two wireless charging areas, while charging and anti-slip protection equipment, killing two birds with one stone. There is a storage board on the right side, and the watch wireless charger can be fixed in the empty slot, and the Apple family bucket can be charged wirelessly through the charging board of the machine. When the storage board is in use, it can be taken out, and it can be pressed back when it is not in use, and it does not take up any space. There is also LE next to itD Charging indicator light.

A good idea, I think in the cylinder body or somewhere to punch two holes, with two electrodes respectively connected to the positive and negative battery, charging the electrode connected to the charger is good, the change is very small, you can try.

How to remove wireless Bluetooth headset charging bay?

1. Check the outside of the charging compartment and look for screws or fixed fasteners. Usually, these screws or clasp will be hidden under a sticker or rubber pad. Use a small screwdriver to remove the screw, or gently pry it with a plastic pry barOpen the buckle. Note that some charging bins may not have screws or clasps, but are secured with adhesive. In this case, you need to be more careful to pry open the charging bay.

2. First, gently open the cover of the charging bin and remove the headphones from the bin. Next, use a special pry bar or thin metal sheet to gently pry open along the seam of the charging compartment. There are usually hidden clasp, once found, press and hold the clasp to easily open the charging bay. After opening the charging compartment, you will see the detailed structure of the interior, as shown in the picture. Note that the battery is connected to the circuit board by a strip of wire.

3,First, open the charging case of the headset and take out the headset. Using a small screwdriver or a coin, remove the four screws from the battery compartment cover. Gently pry open the cover plate, taking care not to exert too much force to avoid damaging the internal parts. Remove the circuit board and cable from the battery compartment one by one. Remove the battery inside the battery compartment, taking care not to damage the battery.